ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: VAG Group (VW - Audi - Seat - Skoda - Bentley) (https://cartechnology.co.uk/forumdisplay.php?fid=55) +---- Thread: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent (/showthread.php?tid=12270) |
RE: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - sidneyjarina - 25-04-2017 Hello Aleck, I am having ODS8024E error when I try to access control units on vehicle. I installed the ODIS-E Original version and I am using a original VAS5054 Bluetooth interface. I tryed to work with a VW37X and VW120 projects and only the gateway control unit can be access in both cases. Do you have some idea about what is happening? RE: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - Aleck - 25-04-2017 (25-04-2017, 14:28 PM)sidneyjarina Wrote: Hello Aleck, Difficult to read this small thread? http://cartechnology.co.uk/showthread.php?tid=12270&pid=233344#pid233344 RE: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - sidneyjarina - 25-04-2017 (25-04-2017, 15:22 PM)Aleck Wrote:(25-04-2017, 14:28 PM)sidneyjarina Wrote: Hello Aleck, Sorry but it is not the same case. My VAS5054 bluetooth interface is working very well. ODIS-E get to read VIN and access the gateway control unit on the vehicle only. When I try to access the others control unit appears the error message ODS8024E. RE: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - Aleck - 27-04-2017 (25-04-2017, 16:42 PM)sidneyjarina Wrote:(25-04-2017, 15:22 PM)Aleck Wrote:(25-04-2017, 14:28 PM)sidneyjarina Wrote: Hello Aleck, The same case. Read careful. RE: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - ROMIKUS - 13-05-2017 What is the difference ODIS ENGINEERING 6.6.1 + Postsetup 66.1.90 Frankenstein Edition and ODIS ENGINEERING 6.6.1 + Postsetup 66.1.90 RE: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - apoelistas - 29-05-2017 I think the difference is language support, for the question above. Perfect version working with my Hardware too, VCX nano USB and Wifi. Other versions (with Key generators) failed to work because I could not get the pop up HW-ID message in order to register my Key ID (thus crashes due to Key generation absence). It could be a windows 8 x64 incompatibility (though I tried windows 7 and windows XP sp3 compatibility mode), or my hardware ID which was ending with xxxxxxxxxxxxxxxxxxxxxxxxxx:LENOVO:4236B87::3 ? I will test to see if I can flash a control unit. RE: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - tecnijl - 05-08-2017 Hi, can anyone tell me if they can do coding with ODIS-E? RE: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - apoelistas - 06-08-2017 Yes you can. I tried it. Not as helpful as VCDs since there is no description. RE: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - hulahans - 09-08-2017 Tried today the Fe install on two different laptops win10 64bit compatibility mode and win7 64bit laptop On both i have no connection ODS8001E and installed odis s after FE I think my vas should be OK, it have OKI and is full as i think. Should i buy a new interface? I did not use Bluetooth i will always connect via USB RE: ODIS Engineering 6.6.1 + PostSetup 66.1.90 (FE+original) + Projects on torrent - Aleck - 09-08-2017 Oki-poki-moki.... this chip is not so important as you think!!! just need good installation. |