VCDS 17.8.1 MULTILANGUAGE FULL - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: VAG Group (VW - Audi - Seat - Skoda - Bentley) (https://cartechnology.co.uk/forumdisplay.php?fid=55) +---- Thread: VCDS 17.8.1 MULTILANGUAGE FULL (/showthread.php?tid=26509) |
RE: VCDS 17.8 MULTILANGUAGE FULL - zomi - 06-12-2017 Just wanted to say thanks Read through all the thread Got a hq 46 clone used usbasp to program it Had some issues with windows 10 with computer not picking up the programmer. Tried on an older windows 7 machine and all was good. Just search for 'Vagcom 16.8.4 full active vcds 16.8.4 DIY Vag com 16.8.4 can reprogram' thats the cable used. hope this helps some sturggling. RE: VCDS 17.8 MULTILANGUAGE FULL - clb - 11-12-2017 (05-08-2017, 16:37 PM)DTech Wrote: VCDS 17.8 MULTILANGUAGE FULLThanks. My VCDS that locked in 2012 can run now. but , i have a question,when runs on 17.8 first time, VCDS need a internet validation for genuine. so, what shall i do? RE: VCDS 17.8 MULTILANGUAGE FULL - gyenge - 19-12-2017 This device could be reprog but no programable pinout . I need to solder on MPC to upgrade ? Or you have other solution RE: VCDS 17.8 MULTILANGUAGE FULL - fantomel - 19-12-2017 Read a little more connect 3 pins on mcp+1 on atmega +gnd, power it up and program it. VCDS 17.8 MULTILANGUAGE FULL - BWF - 21-12-2017 I have problems with long coding with version 17.8.1 in Spanish. Has the same happened to you? Enviado desde mi Redmi 3 mediante Tapatalk RE: VCDS 17.8 MULTILANGUAGE FULL - dadal - 26-12-2017 (05-08-2017, 20:32 PM)fantomel Wrote: Tested on bench, old fashion way, programmer style and it seems to be working.Hi Mate I know this is wrong place but I have just one quenstion : I have read your topic about J-Link and my J-link ( china clone) is now updated to Orginal , all procedure has been successfully completed ( especially thanks for that topic). whichone do you use self ??? and which one do you recommend me ??? ( i do use it for carprog uodate) mIDASLink only works with Analog Devices chips. SAM-ICE only works with Atmel devices. Digi JTAG Link only works with Digi devices. IAR J-Link can not be used with Keil MDK. SEGGER-EDU may only be used for non-commercial purposes. Thanks again Mate RE: VCDS 17.8 MULTILANGUAGE FULL - onliest - 06-01-2018 Hello I have new VCDS, succeful write eprom and flash and ftdi for RL. But VCDS 17.8 it recognizes the device correctly but after connecting to the car constantly breaks the connection and very unstable, the problem is even with reading errors. What could be the reason? RE: VCDS 17.8 MULTILANGUAGE FULL - darek_naprawa - 06-01-2018 Did you program as hw44 or hw46? You may have set security bits wrong. RE: VCDS 17.8 MULTILANGUAGE FULL - DTech - 07-01-2018 First post has been updated. New version of eeproms,flasher and loader. Please read note and pdf inside. RE: VCDS 17.8.1 MULTILANGUAGE FULL - madado159 - 08-01-2018 (08-11-2017, 20:33 PM)d4rk Wrote: Hello, I had the same problem as you, I used vcds 17.8.1 with vcds_loader_v2 under windows 8.1 64 bit. Clone interface 17.1.3 (FW Version: 1.96, HW Version: 0x46) shifting to left after two (2) attempts: before: 611A583A80251A6F088800809400116403557408626D8560E48087000049 after: 583A80251A6F088800809400116403557408626D8560E480870000490000 did you find a solution ?? |