+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: VAG Group (VW - Audi - Seat - Skoda - Bentley) (https://cartechnology.co.uk/forumdisplay.php?fid=55)
+---- Thread: VCDS 17.8.1 MULTILANGUAGE FULL (/showthread.php?tid=26509)
RE: VCDS 17.8.1 MULTILANGUAGE FULL - Joe2 - 19-05-2018
I would like to ask for help and clarification.
I have interface HEX V2 CHINA CLONE (HW 46 and FW was 1.96)
But VCDS 18.2.0 stopped to see interface. So I decided to flash it by USB cable. And it was successful.
But now it is FW 1.95 and VCDS does not want to update it to FW 1.96.
Can I somehow input file Flash1.96_HW_0x46.bin by VCDS USB by software VAGCOM_EEWrite.exe to get FW 1.96 instead 1.95 ?
Or should I program it by USBASP by flash 1.96 ? Please advise where I should connect pins ?
Picture of board sides are in zip attachment.
Thank you for any answer !
RE: VCDS 17.8.1 MULTILANGUAGE FULL - kaalis - 20-05-2018
(19-05-2018, 21:46 PM)Joe2 Wrote: Or should I program it by USBASP by flash 1.96 ? Please advise where I should connect pins ?Start with looking at atmega and follow the pins you need for usbasp programming... mosi, miso, reset, etc. Check info.pdf from loader.
RE: VCDS 17.8.1 MULTILANGUAGE FULL - Joe2 - 20-05-2018
So it is no way to program flash file by USB ?
Eeprom is loding without any problem.
RE: VCDS 17.8.1 MULTILANGUAGE FULL - ZIPPO4594 - 21-05-2018
(20-05-2018, 08:07 AM)Joe2 Wrote: So it is no way to program flash file by USB ?
Eeprom is loding without any problem.
Could you post pcb picture of your câble ?
I think your hex-v2 is fake V2 based on NEC chip, so you can’t upgrade it...
RE: VCDS 17.8.1 MULTILANGUAGE FULL - Joe2 - 21-05-2018
Could you please look into VCDS.zip file in post 291 ? I have placed there pictutres of PCB.
RE: VCDS 17.8.1 MULTILANGUAGE FULL - ZIPPO4594 - 23-05-2018
I don’t know this pcb model. I think it’s not compatible with old car who use dual K-Line protocol (no 16v8 on PCB) but it is not the question !
you can upgrade it, but not sure without usbasp programmer...
RE: VCDS 17.8.1 MULTILANGUAGE FULL - darek_naprawa - 23-05-2018
(16-05-2018, 20:51 PM)pepeEL Wrote: HiUse vcds 17.
I flashed my VCDS 0x46 with latest dump and then use VCDSLoader v6.3 but i test it in my friend VW Passat 2009 and long codding not working. Example i unchecked in Parkhilfe optical illustration then codding. I get info Codding succes and then go and still optical illustration is checked. Also test on other modules and the same problem. I use it with Polish VCDS 18.2.1
Is anybody who can also test it ?
RE: VCDS 17.8.1 MULTILANGUAGE FULL - alibabavl64 - 03-06-2018
(23-05-2018, 18:41 PM)ZIPPO4594 Wrote: I don’t know this pcb model. I think it’s not compatible with old car who use dual K-Line protocol (no 16v8 on PCB) but it is not the question !
you can upgrade it, but not sure without usbasp programmer...
"Logic area" aka "GAL" is present.
Is a good clone (is NOT real HexV2, is ordinary Hex-Can, but a good clone).
RE: VCDS 17.8.1 MULTILANGUAGE FULL - Profi79 - 12-06-2018
hi frend today i updated two vcds cable vcds11.11 and vcds 12.12 to vcds 17.8.0 with usbprog bt guide fantomel and i wtire atmega 162 without problem ,no when i put on the car says status "do not plug on the car" who help me please i trayed with read hdvi nothing not respons
RE: VCDS 17.8.1 MULTILANGUAGE FULL - Multipla2009 - 14-06-2018
Hi any one members, please do you have a soft 17.8.1 italian? Tanks inadvance.