CarProg All Questions/Answers Here! - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10) +--- Thread: CarProg All Questions/Answers Here! (/showthread.php?tid=12004) |
RE: CarProg All Questions/Answers Here! - domelec - 03-04-2017 (03-04-2017, 10:40 AM)dil6222 Wrote:(03-04-2017, 00:31 AM)Enabled Wrote: Ah, so if pin55 is still connected to ground, then I have to lift it. I was hoping it wasn't connected to ground. this is only if the carprog has a track with via from pin 55 some dont and need pin 55 lifting (mine didnt have this track) (03-04-2017, 11:26 AM)aki1 Wrote: Hi C4GMBZDPH5N3H7E9MJGF5RQ8RGZ8YJD4ZEDEU7A2TKTMX9VPNUNGSQSNMRCEHMWF8S RE: CarProg All Questions/Answers Here! - Enabled - 03-04-2017 Hmmm, my pin55 track doesn't 'seem' to be connected to ground? Is this what you guys have? CarProg All Questions/Answers Here! - mikroel - 04-04-2017 (03-04-2017, 20:53 PM)Enabled Wrote: Hmmm, my pin55 track doesn't 'seem' to be connected to ground? Is this what you guys have? No need to be connected to GND Sent from my iPhone using Tapatalk RE: CarProg All Questions/Answers Here! - dil6222 - 04-04-2017 (03-04-2017, 20:53 PM)Enabled Wrote: Hmmm, my pin55 track doesn't 'seem' to be connected to ground? Is this what you guys have?That's what I have and its connected so lift pin or cut track (04-04-2017, 09:10 AM)mikroel Wrote:(03-04-2017, 20:53 PM)Enabled Wrote: Hmmm, my pin55 track doesn't 'seem' to be connected to ground? Is this what you guys have? Hello we know this he wants pin lifting or track cutting so he can program Enabled check your image but on this post I edited to show where to cut RE: CarProg All Questions/Answers Here! - domelec - 04-04-2017 Thats the easy type of carprog to do like said cut the track and use both sides of the cut track mine didnt have this so i had to lift pin 55 RE: CarProg All Questions/Answers Here! - dob12 - 04-04-2017 (04-04-2017, 10:54 AM)domelec Wrote: Thats the easy type of carprog to do Why you want to cut the track In this model pin 55 is not connected to gnd just goes to the other side The photos are a couple of posts above RE: CarProg All Questions/Answers Here! - Enabled - 04-04-2017 That's what I was trying to say. I will wait for my new multimeter to make sure. But I saw that track connected to nothing on both sides. RE: CarProg All Questions/Answers Here! - domelec - 05-04-2017 Then its even easier if its connected to nothing (which i doubt) RE: CarProg All Questions/Answers Here! - dil6222 - 05-04-2017 Pretty sure its connected that hole has a via like I said which is small metal ring pressed in the hole and connects to other side its just been covered by greencoat and filled the hole if you check I'm sure its in ground plane not separate pad but as you say check with voltmeter to be sure. Just a quick side note a via doesn't have to be filled with solder to be connected look at some of the bigger ones on carprog and you can see light through them but there are connected by the pressed ring to the tracks on either side Enabled let me and domelec know the results RE: CarProg All Questions/Answers Here! - Enabled - 05-04-2017 (05-04-2017, 15:34 PM)dil6222 Wrote: Pretty sure its connected that hole has a via like I said which is small metal ring pressed in the hole and connects to other side its just been covered by greencoat if you check I'm sure its in ground plane not separate pad but as you say check with voltmeter to be sure. Will do. I have 2 of these, that I will flash to 8.21. My original one (from 2 years ago), I had to lift the pin, and I was a bit timid about it, as I never did something that small before successfully. But it went well. |