X-tool suppot/Feedback/backup thread - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10) +--- Thread: X-tool suppot/Feedback/backup thread (/showthread.php?tid=18743) |
RE: X-tool suppot/Feedback thread - km666 - 16-10-2017 Ford Focus 2014 Read/Write via OBDII-- OK. RE: X-tool suppot/Feedback thread - octav_kiss - 22-10-2017 Renault modur not work read correct but not write some edc for vag group ,exemple vw touareg RE: X-tool suppot/Feedback thread - pietje001 - 24-10-2017 Ford courier 2016 small screen works by Kuga 2013- RE: X-tool suppot/Feedback thread - pietje001 - 29-10-2017 Renault scenic 2004 obd ok. Peugeot 208 dash obd ok. Bsi obd ok. But then old mileage back. Polo 2011 JC. Old mileage back after 5min. Very strange. RE: X-tool suppot/Feedback thread - Crysis05 - 29-10-2017 WHAT YERS PEUGOUT 208 OBD2 RE: X-tool suppot/Feedback thread - pietje001 - 29-10-2017 (29-10-2017, 09:10 AM)Crysis05 Wrote: WHAT YERS PEUGOUT 208 OBD2 dont know. think 2015/2016 RE: X-tool suppot/Feedback thread - robertbeam26 - 29-10-2017 I use the xtool pro pad2 i had xtool 100 but be care full .car lots use the obd socket - and + wires for the gps locating devise if they should need to repo .well long story short i burnt my wifi dongle when one had wires crossed so i replaced with better .this is a bad issue in my part of U.S.A. and these gps units will interfere with flashing any ecm .one so bad i could not recover it,a new 600 $ unit to beat all . so now i always check before i hook up my $ machine .factory will not replace a burn part of any unit is what i was told . RE: X-tool suppot/Feedback thread - volavka - 29-10-2017 (29-10-2017, 16:27 PM)robertbeam26 Wrote: I use the xtool pro pad2 i had xtool 100 but be care full .car lots use the obd socket - and + wires for the gps locating devise if they should need to repo .well long story short i burnt my wifi dongle when one had wires crossed so i replaced with better .this is a bad issue in my part of U.S.A. and these gps units will interfere with flashing any ecm .one so bad i could not recover it,a new 600 $ unit to beat all . so now i always check before i hook up my $ machine .factory will not replace a burn part of any unit is what i was told . My friend .you're getting a little bit confused we are discussion x-tool that's used for ODOMETER not the chinese tool called xtool pad or so RE: X-tool suppot/Feedback thread - pietje001 - 07-11-2017 Next week xtool will get new update for vw mqb flatform. golf7 etc. RE: X-tool suppot/Feedback thread - xm3n - 08-11-2017 (07-11-2017, 20:46 PM)pietje001 Wrote: Next week xtool will get new update for vw mqb flatform. golf7 etc. Yess I got GOLf 7 to test |