+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3)
+--- Forum: CARRADIO / NAVIGATION (https://cartechnology.co.uk/forumdisplay.php?fid=14)
+--- Thread: OPEL_SD_2016-2017 (/showthread.php?tid=19633)
OPEL_SD_2016-2017 - benyclaudiu - 17-11-2016
Update navi 600-900 2016-2017
CID To read the original SD:
cat / sys / block / mmcblk0 / device / cid
You will need a Samsung EVO+ SD card and a Linux(Ubuntu) PC with integrated SD card reader, the ones on USB don't work.
1.Copy the map content on the SD.
2.Use the tool change_cid to change the CID of the SD
After you insert the SD check under /dev and look for mmcblkx (can be 0,1,2 etc)
In my case is mmcblk0, run the application from the current folder
for 32bit version use the command like this: sudo ./change_CID_32 /dev/mmcblk0 5d53424c32424d31013917ca53010400
for 64but version use the command like this: sudo ./change_cid /dev/mmcblk0 5d53424c32424d31013917ca53010400
"thanks" or "Add a reputation"
RE: OPEL_SD_2016-2017 - number7 - 25-11-2016
When I change CID it is written - SUCCESSFULLY !!
but when I check CID by "CAT" CID shows:
5d53424c32424d31013917ca53010401
after few tries is the same - "1" on the end insted "0".
RE: OPEL_SD_2016-2017 - benyclaudiu - 25-11-2016
We must put an end without the two zeros CID 5d53424c32424d31013917ca530104
RE: OPEL_SD_2016-2017 - benyclaudiu - 03-12-2016
To read the CID in SD:
cat / sys / block / mmcblk0 / device / cid
mmc0: 59b4 = you a fake card
mmc0: 0001 = card OK
RE: OPEL_SD_2016-2017 - RuLe - 13-12-2016
How can i change cid_ i need tool
RE: OPEL_SD_2016-2017 - benyclaudiu - 15-12-2016
1 - Card EVO + (I tried 32G and 64G SD)
2 - FAT32 formatted card (in Windows) and copy navpsf_update in rrot (corrected)
3 - Install Ubuntu 32/64 (64's what I used)
4 - Copy local (Desktop linux) folder VW
5 - open the copied folder and right cick -> "open terminal"
6 - check with the command execution rights "ll". You must have attributes besides "r", "w" and a "x".
If there is an X writes: "chmod 777 mmc32" linux if you have 32 or "chmod 777 mmc64" if you have linux 64.
And the rights and check the "ll"
7 - Insert the SD slot. Terminal command "df" and verify the name card.
Somewhere down everything must occur "mmcblk0" + p + a number.
The suffix p "number" is the partition on the card, we are not interested, just use "mmcblk0".
CID To read the original SD:
cat / sys / block / mmcblk0 / device / cid
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
8 - Order To change CID terminal:
- Linux 32
sudo ./mmc32 prog_cid / dev / mmcblk0 5d53424c32424d31013917ca53010400
- Linux 64
sudo ./mmc64 prog_cid / dev / mmcblk0 5d53424c32424d31013917ca53010400
After this command will display:
Writing new CID: 5d53424c32424d31013917ca53010400
Success! Remove and Reinsert SD card to check new CID.
To read the SD CID changed:
SD disassemble and remove it from the linux PC SD reader, and then paste it into the PC
cat / sys / block / mmcblk0 / device / cid
will be displaying the new CID 5d53424c32424d31013917ca53010400
RE: OPEL_SD_2016-2017 - RuLe - 19-12-2016
(15-12-2016, 18:22 PM)benyclaudiu Wrote: 1 - Card EVO + (I tried 32G and 64G SD)
2 - FAT32 formatted card (in Windows) and copy navpsf_update in rrot (corrected)
3 - Install Ubuntu 32/64 (64's what I used)
4 - Copy local (Desktop linux) folder VW
5 - open the copied folder and right cick -> "open terminal"
6 - check with the command execution rights "ll". You must have attributes besides "r", "w" and a "x".
If there is an X writes: "chmod 777 mmc32" linux if you have 32 or "chmod 777 mmc64" if you have linux 64.
And the rights and check the "ll"
7 - Insert the SD slot. Terminal command "df" and verify the name card.
Somewhere down everything must occur "mmcblk0" + p + a number.
The suffix p "number" is the partition on the card, we are not interested, just use "mmcblk0".
CID To read the original SD:
cat / sys / block / mmcblk0 / device / cid
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
8 - Order To change CID terminal:
- Linux 32
sudo ./mmc32 prog_cid / dev / mmcblk0 5d53424c32424d31013917ca53010400
- Linux 64
sudo ./mmc64 prog_cid / dev / mmcblk0 5d53424c32424d31013917ca53010400
After this command will display:
Writing new CID: 5d53424c32424d31013917ca53010400
Success! Remove and Reinsert SD card to check new CID.
To read the SD CID changed:
SD disassemble and remove it from the linux PC SD reader, and then paste it into the PC
cat / sys / block / mmcblk0 / device / cid
will be displaying the new CID 5d53424c32424d31013917ca53010400
thanks for the reply, I tried as you say, but when I do the command returns the old cid
RE: OPEL_SD_2016-2017 - benyclaudiu - 20-12-2016
Terminal CID OPEL
RE: OPEL_SD_2016-2017 - number7 - 23-12-2016
(03-12-2016, 13:52 PM)benyclaudiu Wrote: To read the CID in SD:
cat / sys / block / mmcblk0 / device / cid
mmc0: 59b4 = you a fake card
mmc0: 0001 = card OK
Fake card?
What's on Your mind? Cloned by China?
RE: OPEL_SD_2016-2017 - batja - 30-12-2016
Please torrent or uploaded cryptnav..thanks