+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: VAG Group (VW - Audi - Seat - Skoda - Bentley) (https://cartechnology.co.uk/forumdisplay.php?fid=55)
+---- Thread: VCDS 17.8.1 MULTILANGUAGE FULL (/showthread.php?tid=26509)
RE: VCDS 17.8.1 MULTILANGUAGE FULL - mattdj - 19-05-2019
(18-05-2019, 13:49 PM)ZIPPO4594 Wrote: if i can, with pleasure !
what is your usb programmer ? USBASP ?n (i use this one and works fine)
what is your HW model ? 044 or 046 ?
if you want re download VCDSLoader 7.2 Package (works fine with french vcds 18.9, not tested with other language)
Yes,I'm use usbasp and HW is 046.
I retried to redownload but nothing
RE: VCDS 17.8.1 MULTILANGUAGE FULL - darek_naprawa - 19-05-2019
Polish langue 18.9 not work.
Only 18.2 work ok.
RE: VCDS 17.8.1 MULTILANGUAGE FULL - alsamaraee - 20-05-2019
Hi I did the repair and loader works fine. but still have same problem (can not ready) this killing me. Please any help
RE: VCDS 17.8.1 MULTILANGUAGE FULL - PhilipArt - 20-05-2019
(20-05-2019, 09:48 AM)alsamaraee Wrote: Hi I did the repair and loader works fine. but still have same problem (can not ready) this killing me. Please any help
You tried with the cable connected to your car? If so, are you sure your car supports the can protocol?
RE: VCDS 17.8.1 MULTILANGUAGE FULL - alsamaraee - 20-05-2019
(20-05-2019, 10:31 AM)PhilipArt Wrote:(20-05-2019, 09:48 AM)alsamaraee Wrote: Hi I did the repair and loader works fine. but still have same problem (can not ready) this killing me. Please any help
You tried with the cable connected to your car? If so, are you sure your car supports the can protocol?
Yes the cable is connected to the car.
My car is an AUDI A6 2006, so it supports can protocol. I used the cable before on the same car. tills it start showing CAN not ready. I don't think there is somthing wrong with my CAN cause I connected the car on other OBD2 (autocom) diagnos and it's work just fine.
RE: VCDS 17.8.1 MULTILANGUAGE FULL - PhilipArt - 21-05-2019
I had a similar issue with the last (18.9.1) version and i had to change the usb ports to enable can - also try to check if the cable it's connected correct, or if any of the obd pins it's bended (pin 6 or 14).
RE: VCDS 17.8.1 MULTILANGUAGE FULL - alsamaraee - 21-05-2019
(21-05-2019, 06:51 AM)PhilipArt Wrote: I had a similar issue with the last (18.9.1) version and i had to change the usb ports to enable can - also try to check if the cable it's connected correct, or if any of the obd pins it's bended (pin 6 or 14).
I did no change
RE: VCDS 17.8.1 MULTILANGUAGE FULL - mattdj - 25-05-2019
But whit Tl866II I can programm the interface with fuse bits locked?
RE: VCDS 17.8.1 MULTILANGUAGE FULL - alsamaraee - 27-05-2019
(21-05-2019, 06:51 AM)PhilipArt Wrote: I had a similar issue with the last (18.9.1) version and i had to change the usb ports to enable can - also try to check if the cable it's connected correct, or if any of the obd pins it's bended (pin 6 or 14).
It was pi 14. even the soldring looks very fine. now it’s work.
RE: VCDS 17.8.1 MULTILANGUAGE FULL - mattdj - 02-06-2019
nobody can help me?