Ddt4all - full set - Renault/Dacia - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: Renault - Dacia - Nissan - Infiniti (https://cartechnology.co.uk/forumdisplay.php?fid=57) +---- Thread: Ddt4all - full set - Renault/Dacia (/showthread.php?tid=28283)

Ddt4all - full set - Renault/Dacia - jenny123 - 29-09-2017 Hello All In this package you will find full set DDT4ALL necessary to run on Windows 7 32bit (x86). Installation procedure: 1. python-2.7.13.msi 2. PyQt4-4.11.4-gpl-Py2.7-Qt4.8.7-x32.exe 3. Unpack ddt4all-master.zip to C:\Python27\Scripts\ 4. Unpack ecus.rar to C:\Python27\Scripts\ddt4all-master\ To run: 1. Open Command Prompt from Accessories or type CMD in Start Search Window 2. Type "cd\" and hit Enter 3. Type "cd c:\python27\scripts\ddt4all-master" Enter 4. Type "ddt4all.py" Enter Set up connection for ELM327 and have fun. To do any changes you need click on EXPERT MODE first! Tested with Renault Clio III 2010 1.2 tce (miles to km) and Renault Clio IV 2014 1.2 (miles to km - need to disconnect battery after programming). Any questions, just let me know, try to help. Packed with Winrar 5.10, do not use Winrar 4.xx to unpack. Second Version -> Installation file thanks to DaciaKlub -> just install and start from Start Menu or Desktop Icon. If you find it useful pls hit Thanks and Rep+ NO PASS BR, J. RE: Ddt4all - full set - Renault/Dacia - mitsos - 08-11-2018 hi I have some STN1110, the default baudrare is 9600. I don't find the way to change to 38400. How can I change the settings of ddt4all to include 9600? The famous KKL interface is it working with ddt4all? regards mitsos RE: Ddt4all - full set - Renault/Dacia - mattydr67 - 09-11-2018 Why don't you change the baud rate of your STN1110 from 9600 to 38400? Much easy I suppose so. Try this application Good luck Document.docx File Type: Downloaded: 161 times Size: 11.83 KB RE: Ddt4all - full set - Renault/Dacia - mitsos - 10-11-2018 hi this small exe after some tries, find the serial number and firmware version of STN1110 but in the Baudrate drop down menu there is nothing to select, so it is impossible to change its baudrate by this way. According to datasheet I can change the baudrate during its using but I cannot store this to non-volatile memory. I moving next next to ddtall application and I make these changes: in options.py, I change the "port_speed = 38400" to "port_speed = 9600" in ddt4all.py, I change the "portSpeeds = [38400, 57600, 115200, 230400, 500000]" to "portSpeeds = [9600, 38400, 57600, 115200, 230400, 500000]" and also the "self.selectedportspeed =38400" to "self.selectedportspeed = 9600". After these changes I have in dropdown menu the 9600 selection and the ELM Benchmark it is working. On connected mode the ddt4all only sends an ATZ to stn1110, nothing else. Is that correct? These experiments are doing in my workshop and I connect nothing to the car. regards mitsos RE: Ddt4all - full set - Renault/Dacia - rere - 01-01-2019 install ok, but i use a obd small elm 327 buetooth 4.0, baud is 38400, very low speed, i can"t read ecu, all data area stay in red, have you a idea for have a better dial pc to obd sensor,