1999 VW Jetta VR6 how to read ECM - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: CHIPTUNING (https://cartechnology.co.uk/forumdisplay.php?fid=12) +--- Thread: 1999 VW Jetta VR6 how to read ECM (/showthread.php?tid=35680) Pages:
1
2
|
1999 VW Jetta VR6 how to read ECM - koziol - 15-05-2018 Can someone provide me with procedure how to read ECM for 1999 VW Jetta VR6 ECM BOSCH 021 906 018B costumer wants to add some power. RE: 1999 VW Jetta VR6 how to read ECM - Remap Ross - 15-05-2018 (15-05-2018, 21:12 PM)koziol Wrote: Can someone provide me with procedure how to read ECM for 1999 VW Jetta VR6 me7? kess will do, might not be under jetta but perhaps golf or look up protocols RE: 1999 VW Jetta VR6 how to read ECM - koziol - 15-05-2018 Kess says some kind of error, MPPS V18 no successes, galetto 1260 no success MPPS v13 no success non of this programmers has this listed , they can read ECM ID thats it nothing ales RE: 1999 VW Jetta VR6 how to read ECM - rs@chip - 15-05-2018 try read it with old VAG-Comander and galletto cable thru K-line..If not sucess than read by external programer..here is small softwere which work by most k-can RE: 1999 VW Jetta VR6 how to read ECM - Remap Ross - 15-05-2018 if read with old galletto make sure u checksum first RE: 1999 VW Jetta VR6 how to read ECM - naphosim - 16-05-2018 (15-05-2018, 21:12 PM)koziol Wrote: Can someone provide me with procedure how to read ECM for 1999 VW Jetta VR6 hi, it is possible in 1999 the ecu to be equipped with Eprom not Flash, so this is the reason you can read just the ID. RE: 1999 VW Jetta VR6 how to read ECM - koziol - 16-05-2018 so what the procedure than RE: 1999 VW Jetta VR6 how to read ECM - koziol - 17-05-2018 Thats how it looks RE: 1999 VW Jetta VR6 how to read ECM - Enabled - 19-05-2018 You can always do boot mode for amf29f400BB. Ground to pin 24 of 29f400bb for 5 seconds as you are powering up. Galletto1260 has it listed under Audi Boot mode. It will be very wise for a backup too. RE: 1999 VW Jetta VR6 how to read ECM - ROD-BENDERS - 19-05-2018 (15-05-2018, 21:51 PM)koziol Wrote: Kess says some kind of error, MPPS V18 no successes, galetto 1260 no success Some of the older pre-me7 ecu can write only with mpps. Use mpps m5x protocol which will also write the m3x as well. But first you will need to find the ori file as there is no read option on these ecu with mpps, write is ok. Two ecu types are listed for Jetta V6; ME7.1.1 and M5.92 see pic Kess Galletto will not do M3x M5x ecu |