+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: NBT Evo bricked (/showthread.php?tid=39165)
Pages:
1
2
NBT Evo bricked - hiho199 - 05-09-2018
Hey there,
this is my first post, hope someone helps me on this:+
I have sucessfully bricked an NBT Evo on my testbench when upgrading Bootloader via E-Sys (no loader when flashing active):
It flashed the bootloader and gave this error:
[HU_NBT2 - 63 - btld_00001ffd-001_052_004] Transaction type: blFlash; Message: 1% Fortschritt bei ECUId:HU_NBT2_0x63 [100% von btld_00001ffd-001_052_004] [TRANSACTION]
[] Job-Ausführung ist fehlgeschlagen: negative response error:
code: repeat job
description: service RoutineControl CheckMemory IndicatedCheckValue returned unexpected result: debugInformation_02_FF; LinkName: HU_NBT2_63_ETHERNET_63
severity: FATAL ERROR
[THROWABLE]
Now the fan runs full speed and the display shows "no signal". I cannot access it via tool32 and esys does not see it either. Is there a way to flash the bootloader using the serial console/connection? Is there another way to make this thing programmable again?
Best - Marvin
RE: NBT Evo bricked - ltujustas - 05-09-2018
What esys you using ? With launcher ? Try latest esys with pszdata without launcher and ICOM not enet
RE: NBT Evo bricked - hiho199 - 06-09-2018
Hi, thx for your reply. I’m using esys 3.32 without launcher. i will try using icom instead of Ethernet.
RE: NBT Evo bricked - BMWdriva - 06-09-2018
(06-09-2018, 06:10 AM)hiho199 Wrote: Hi, thx for your reply. I’m using esys 3.32 without launcher. i will try using icom instead of Ethernet.connect icom dhcp,and flash in esys HU_NBT2
RE: NBT Evo bricked - DJ_B4L - 14-10-2018
did you get it running using icom
RE: NBT Evo bricked - hiho199 - 16-10-2018
hey, thanks for asking.
I did NOT get it running via ICOM. I can't even access it via UART...
All I get is a reboot loop which displays this:
IPL: B140,D1,14233B[2014-06-04 11:32:07],J5,PG3.0,GL-N=128(4),RAM=256,RST=9
CLK: 720/600/400 MHz (ARM/DSP/DDR)
IOC: 32000000 013100ff 02000000 00530000
Any Ideas on how to get this thing in serial boot to actually load some IPL or flash the memory, so that it would at least boot again?
RE: NBT Evo bricked - Vias - 15-11-2018
Hello everyone!
I have same the problem))
IPL: B140,D1,14233A[2014-06-04 11:32:07],J5,PG3.0,GL-N=128(4),RAM=256,RST=9
CLK: 720/600/400 MHz (ARM/DSP/DDR)
IOC: 32000000 01310f00 02000000 00530000
BREAK detected - press any key to stop the ipl within 5000ms! => BREAK accepted! 3
Who knows how to solve a problem, and recover bootloader?
RE: NBT Evo bricked - graphys - 13-01-2019
Can anyone fix this problem?
RE: NBT Evo bricked - vilord - 14-01-2019
is the bootloader something that is installed on the hard drive in the evo? it might be possible to use DD to copy from a good evo to that bad one and then re-run the flash?
RE: NBT Evo bricked - bmwcoder75 - 14-01-2019
(14-01-2019, 00:44 AM)vilord Wrote: is the bootloader something that is installed on the hard drive in the evo? it might be possible to use DD to copy from a good evo to that bad one and then re-run the flash?
No such thing as a btld installed on a hdd in evo my friend