CarTechnoloGY
ISTA+ 4.10 The vehicle could not be identified. ENET CABLE - Printable Version

+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: ISTA+ 4.10 The vehicle could not be identified. ENET CABLE (/showthread.php?tid=42367)



ISTA+ 4.10 The vehicle could not be identified. ENET CABLE - Claudio.79 - 15-11-2018

Hello everybody!

I'm trying to connect F31 using ISTA+ 4.10 running on Windows 10 but with no result.

When I select connect to vehicle  i got always error message:

The vehicle could not be identified. Please check the access to the vehicle and check whether the testing-analysis-diagnosis has been activated.

Doesn't work  on direct connection, or any other selection.

Brand selection is BMW/Mini, same BMW/PKW.

Pinging the car's IP address from promp it's ok.

If I connect ENET Cable with BMWAicoder it works, ESYS works.

Any ideas?


Thanks for help!!!


RE: ISTA+ 4.10 The vehicle could not be identified. ENET CABLE - willisodhiambo - 16-11-2018

Check your Ediabas.ini file. Correctly set up interface for ENET?


RE: ISTA+ 4.10 The vehicle could not be identified. ENET CABLE - Claudio.79 - 16-11-2018

I have two folder of ediabas, one on C: and another one in C:\Rehingold\ediabas, i configured by ediabas configurator selecting ENET , Autodetect, port 6801,6811.
Then copy file on both folder.
Still not working, ZWG is always blank, also after refresh.

Still not working also after LAN con figurati on with IP 169.254.1.1

What i should try?


RE: ISTA+ 4.10 The vehicle could not be identified. ENET CABLE - Fatalix - 16-11-2018

Have you tried selected ICOM / ENET direct connection under interface options in ISTA+?


RE: ISTA+ 4.10 The vehicle could not be identified. ENET CABLE - Claudio.79 - 16-11-2018

Solved!!

Thanks to everybody!

Connection problem was due to a VirtualBox Network Adapter, after disable it ISTA+ recognize the ENET cable.
But it's not possible to complete the vehicle test, always get error:
The programming system could not be initailized. The ISTA installation may be damaged or incorrectly configured. Reinstall ISTA. If problem persist contact local support.

What's wrong now???


RE: ISTA+ 4.10 The vehicle could not be identified. ENET CABLE - Bimmer540 - 16-11-2018

C: EDIABAS



EDIABAS.INI

#################
;# EDIABAS 7.3.0 #
;#################

;=============================================================================
[Configuration]
;=============================================================================
Interface =ENET

And in ista+ Ediabas connection


RE: ISTA+ 4.10 The vehicle could not be identified. ENET CABLE - Claudio.79 - 17-11-2018

Thank to all!
It was enough to disable the VirtualMachine NetworkAdapter,

now it's not possible to perfom the complete test of the vehicle, i will try to reinstall everything from zero.

i get this error:
The programming system could not be initailized. The ISTA installation may be damaged or incorrectly configured. Reinstall ISTA. If problem persist contact local support.

What i should do??