BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image

BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - Printable Version

+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image (/showthread.php?tid=4290)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

RE: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - etronic - 05-07-2014

I got problem with ISTA D on any F-series cars

Mainly it can not identify car at all. When I type VIN and try to connect to car, it still says that it can't identify it (VIN is in database as it shows all cars spec). Same ICOM works fine on all F cars with older software. All E-series cars are fine.... Also programming for F-cars is working fine too. Just ISTA D has this problem....

RE: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - apple - 10-07-2014

A simple thanks is not enough.
Great work Sir.
Thank you again.

RE: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - gf3106 - 14-07-2014

Is it possible to install a K+DCAN emulator onto this image? I have the install running on dell laptop perfectly but would like to use with a built-in emulator & K+DCAN. Thanks

RE: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - ahmedmph - 14-07-2014

Hello every body,

I have issue with ISTA/P, error is coming while checking car F10 as shown in below screenshot
any suggestions

RE: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - kawkaw - 16-07-2014

(14-07-2014, 21:32 PM)ahmedmph Wrote: Hello every body,

I have issue with ISTA/P, error is coming while checking car F10 as shown in below screenshot
any suggestions

i think you need to put the car on alimentation for 14v on T15, and 14V on T30 for programming

RE: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - 2013m5 - 16-07-2014

(14-07-2014, 21:32 PM)ahmedmph Wrote: Hello every body,

I have issue with ISTA/P, error is coming while checking car F10 as shown in below screenshot
any suggestions

The battery voltages are ok, make sure use power supply for programming.
Here try these steps below for Castor error.
1. Disconnect the battery for 30 minutes.
2. Reconnect the battery.
3. Reboot the computer.
4. Re-read the vehicle.
Let us know if you still have the Castor error.

Hope this help,

(05-07-2014, 19:32 PM)etronic Wrote: I got problem with ISTA D on any F-series cars

Mainly it can not identify car at all. When I type VIN and try to connect to car, it still says that it can't identify it (VIN is in database as it shows all cars spec). Same ICOM works fine on all F cars with older software. All E-series cars are fine.... Also programming for F-cars is working fine too. Just ISTA D has this problem....

Did you try VCI config for connection?

RE: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - TizWoz - 16-07-2014

Did you look at point [6] of the first post on the following link

http://garage-automotive.com/showthread.php?tid=5242

RE: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - dardan - 18-07-2014

Hi first of all thank you for the great work Zekan...

Allthough I`m having some strange issue, whenever i plug ICOM cable to my laptop I got the "switch connection mode to lan in progress" I have set the connection to direct offline 100 time and this still pops up whenever I put on the cable.

Did you experience this issue, is there some workaround, did I miss something?

thnx

RE: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - petkowo - 22-07-2014

Hello guys, I have problem with my original ICOM interface with the newest firmware (3.10.45). I have still red dot status in ISTA-P. I used before ICOM clone and it works fine, but it is dead sad

I don´t know why, it has red light for one hour in one E60... then I disconnect it and now I can´t load it. Can anybody help me with RED DOT status and with my ICOM clone retrieve pls.

PS: I have that same RED DOT status in online BMW OSS sad

RE: BMW ISTA/D Rheingold 3.42.40 ISTA/P 2.52.40 Asus F3 HDD image - spiridon - 23-07-2014

Hi guys in need Greek language pack (streamdataprimitive_GR) where are find ?
Many thanks in advance.