+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: ZBE3 is not working anymore after I-Step Update with E-Sys (/showthread.php?tid=46841)
ZBE3 is not working anymore after I-Step Update with E-Sys - reclaim - 18-02-2019
Hello,
i have retrofited the HU_NBT2 the Touchbox and the Touchcontroller in my F20 BJ:2012.
Now i have tryed to update my I-Steps to 18-07-531.
I updated with modifyed FA the HU_NBT2 and with the orginal FA: FEM_GW, FEM_Body, ACSM, DME, REM, Kombi and EPS.
Now my Problem is that after i updated the orginal SGs the Retrofited ZBE3 is not working anymore.
In E-Sys (load ECU) its not listed and Rheingold says "SG not found".
I don´t have flashed the ZBE3. I don´t know why its not working anymore.
Can you help me?
Thanks
RE: ZBE3 is not working anymore after I-Step Update with E-Sys - benoos - 18-02-2019
Before update everything worked?
ZGW module should be updated before other modules. You can check PreRequisite in E-Sys TAL editor
RE: ZBE3 is not working anymore after I-Step Update with E-Sys - reclaim - 18-02-2019
Yes, before the update the Controller works fine.
At the moment all SG aro on F20-18-07-531 exept the Touch Controller, i didn´t flash it.
With my old CIC Controller (ZBE2) installed i can controll with the iDrive System.
RE: ZBE3 is not working anymore after I-Step Update with E-Sys - benoos - 18-02-2019
Have you proper coding for it? What Zeitkriterium you use?
On SVT list is there ZBE2 still?
RE: ZBE3 is not working anymore after I-Step Update with E-Sys - reclaim - 18-02-2019
I have tried it with ZK 0717 and 0718.
When the ZBE3 is connected E-Sys doesen´t show any ZBE device in SVT (when i klick Load ECU)
Is the ZBE2 connected E-Sys show it as ZBE2.
RE: ZBE3 is not working anymore after I-Step Update with E-Sys - sebastianfernandes - 19-02-2019
My guess is probably your svt is not updated with zbe3. it still has the zbe2 in it.
thats why its not showing up.
when you read svt it shows zbe2?
when you read ecu it shows zbe2?
would be worth a try to delete zbe2 from svt and update vcm then read ecu again see if zbe3 shows up and then write the new config in vcm.
happens also when retrofitting from bkombi to dkombi because of same diag address it uses.
of course first save your original svt before you try to make any changes..
RE: ZBE3 is not working anymore after I-Step Update with E-Sys - reclaim - 19-02-2019
Can you perhaps write a Little How to Update VCM and delete ZBM2?
RE: ZBE3 is not working anymore after I-Step Update with E-Sys - CEBEP - 19-02-2019
Go to esys options
Mark update vsm update msm
Read fa
Activate fa
Code any ecu in tree
Read ecu and see zbe now
RE: ZBE3 is not working anymore after I-Step Update with E-Sys - reclaim - 19-02-2019
Thank you i will try this later
RE: ZBE3 is not working anymore after I-Step Update with E-Sys - reclaim - 19-02-2019
After updating the VCM i can see ZBE3 again and after VO Coding its working.
Again Thank you.