+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3)
+--- Forum: CHIPTUNING (https://cartechnology.co.uk/forumdisplay.php?fid=12)
+--- Thread: SMART CITY COUPE Default Map 004-383 (/showthread.php?tid=46944)
SMART CITY COUPE Default Map 004-383 - GorylAliasGonzo - 20-02-2019
Hello,
I'm searching default map for SMART City-Coupe 1999 0,6 HW 0261205004 SW 1037356383.
Second question if I can replace that map with HW 004 and SW 835.
Maybe someone have WinOLS project which I can get for learning.
Thank you.
RE: SMART CITY COUPE Default Map 004-383 - yudon - 20-02-2019
There is such file.
As for the replacement of SW - the question is not clear.
What is the purpose of such a process?
RE: SMART CITY COUPE Default Map 004-383 - GorylAliasGonzo - 21-02-2019
(20-02-2019, 21:32 PM)yudon Wrote: There is such file.
As for the replacement of SW - the question is not clear.
What is the purpose of such a process?
I found some ready files already with name HW004 SW383 and when I load them I see HW004 and SW835.
RE: SMART CITY COUPE Default Map 004-383 - GorylAliasGonzo - 22-02-2019
Hello,
I have used the file from above and now ECU is bricked. I have start flashing and it show up Writing error. At the moment I can run the car and when reading car I have just "...'''000000'''..."
Any one can help?
RE: SMART CITY COUPE Default Map 004-383 - yudon - 22-02-2019
The problem is not in the firmware file. The problem is in the writing process.
You write through the OBD or in Boot mode?
RE: SMART CITY COUPE Default Map 004-383 - GorylAliasGonzo - 22-02-2019
(22-02-2019, 10:57 AM)yudon Wrote: The problem is not in the firmware file. The problem is in the writing process.
You write through the OBD or in Boot mode?
OBD I did in the past already with OBD via Galletto only read is not possible via Galletto.
RE: SMART CITY COUPE Default Map 004-383 - yudon - 22-02-2019
Try to read/write using boot mode.
RE: SMART CITY COUPE Default Map 004-383 - GorylAliasGonzo - 22-02-2019
(22-02-2019, 12:22 PM)yudon Wrote: Try to read/write using boot mode.
I need to take out the ECU to do boot mode.
Could you tell me which PIN's? I know 110 is K-Line.
RE: SMART CITY COUPE Default Map 004-383 - yudon - 22-02-2019
(22-02-2019, 12:47 PM)GorylAliasGonzo Wrote:(22-02-2019, 12:22 PM)yudon Wrote: Try to read/write using boot mode.
I need to take out the ECU to do boot mode.
Could you tell me which PIN's? I know 110 is K-Line.
It seems like this
RE: SMART CITY COUPE Default Map 004-383 - GorylAliasGonzo - 23-02-2019
Working again. Done reflash on the table with Galletto V57.
After re flash was still showing only 0000 when try to get ID but after putting into car it get to work and start reading again properly. Thank you.