+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3)
+--- Forum: CARRADIO / NAVIGATION (https://cartechnology.co.uk/forumdisplay.php?fid=14)
+--- Thread: Solved ✔ Mercedes w216 CL500, problems with Comand (/showthread.php?tid=54998)
Mercedes w216 CL500, problems with Comand - koskja - 13-08-2019
Hello,
I’m trying to figure out what my CL’s previous owner has done:
Car is imported from Japan. When I bought it, comand screen was dead but radio was working ok for some time, and radio info was shown on instrument cluster display. Comand center knob nor surrounding buttons didn’t work on center console.
Got the car home and pulled comand out, figured that one pair of “telematics” CAN wires were disconnected as well as one “30g” wire which comes from rear SAM. Plugged the wires back to to the connector and center knob started to work again.
Comand won’t wake up nor go to sleep when I turn the key, it has to be turned on and off using the button in center console.
It works like key is turned to off position even when car is running, and comand is turned on with on/ off button.
I can see the climate control info on comand screen but info won’t change no matter what I do with AC.
If I push multicontour seat button, comand screen says to turn on the ignition.
If I try to access vehicle settings, comand screen says to turn on the ignition.
I cannot change the language from comand menu, it’s not active.
Radio info won’t be displayed on instrument cluster display, only “- - - -“ is shown.
Steering wheel volume up and down buttons don’t work, although they did work earlier when driving home.
There is no radio presets shown - is tuner not turned on?
When I bought the car, I did have an access to tuner with Star, no I don’t. I can’t access to comand, tuner or central display.
Question is, does the amplifier get the wake up signal first when key is turned, and could the signal be missing?
I have wiring diagrams for Japanese comand, could someone help with H/K amp diagram?
I’ll perform a new quick test later today and post the fault codes.
Thank you in advance!
RE: Mercedes w216 CL500, problems with Comand - DBCT - 13-08-2019
You don't have the star diagnosis tool? You should at least download a copy of WIS for this kind of a task.
RE: Mercedes w216 CL500, problems with Comand - koskja - 13-08-2019
I do have star but not wis. Few schematics would be a life saver. Found a site called star tekinfo but I don’t have a clue can I use it from Estonia.
RE: Mercedes w216 CL500, problems with Comand - koskja - 13-08-2019
UCP - Upper Control Panel
No CAN message was received from control unit N93 (Central gateway control unit). Failure of CAN message “Air conditioning”
Event no. 9034, Current and stored.
IC - Instrument Cluster
No can message was received from control unit COMAND
Event no. C02F Current and stored.
No can message was received from control unit COMAND
Event no. C037 Current and stored.
RFK - Rear backup camera
No CAN message from control unit COMAND
Event no. 8603 Current and stored.
No CAN message from control unit A1 (Instrument cluster)
Event no. 8604 Current and stored.
DCM-FL- Door Control Module front left
9066 Control unit N69/1 (Left door control unit) Defective, Current and stored
RE: Mercedes w216 CL500, problems with Comand - koskja - 13-08-2019
Case closed, aftermarket digital tv tuner was broken and left CAN line open between comand and x30/20 central CAN distributor. Happy times.
I’m an ex mercedes diagnostic technician but haven’t been working with cars over 10 years.