Renolink Support/Feedback - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: IMMO & LOCKSMITH (https://cartechnology.co.uk/forumdisplay.php?fid=9) +--- Thread: Renolink Support/Feedback (/showthread.php?tid=56563) |
Renolink Support/Feedback - volavka - 17-09-2019 Let share your experiense about this tool Regards RE: Renolink Support/Feedback - Abou-raffik - 17-09-2019 first of all special thank for cartechnology owner for this helpful thread making. hi all my friends i have problem with symbol II with ecu v42 after dead battery i try to learning ecm using renolink v182 -renolink v182 -car logan 2 2015 year -problem:virgin uch after dead battery what i do keys uch t4 logan2 sendero2....ecm learning. -read pin =read ok pin code +isk key (id key 1 and 2 with 00 00 00 00 value)!!! -connect -start learning -validate -disconnect try to start but wont to start. finally i try with uch blank icon but same any one can guide me please (there is 500 km between me and the first near dealer). thankyou in advance RE: Renolink Support/Feedback - ivica21 - 18-09-2019 Airbag reset work perfect only on Twingo after reset crash must make configuration. Renault Megane 2 card programing not work so good and make only one card valid and i use other tool. Renault Scenic 3 card program not work good so i use other tool. Steering lock virgin work good. Configuration for dashboard (Renault Scenic 3,Megane 3,Megane 4,Scenic 4 after some configuration remove + positive from acu. and reconnect) if you make mistake you will have error prog but you can make auto configuration via Renault Clip. RE: Renolink Support/Feedback - mitch3 - 18-09-2019 (17-09-2019, 22:48 PM)BOULEFAA Wrote: first of all special thank for cartechnology owner for this helpful thread making.If you virginize uch you Must do : write pin on uch after that learn keys and after that learn ecu to learn ecu use xml(diagnostic running) RE: Renolink Support/Feedback - fantomel - 18-09-2019 When you write Feedback or Problems write also what Renolink Version you used since are a lot of them. RE: Renolink Support/Feedback - Abou-raffik - 18-09-2019 If you virginize uch you Must do : write pin on uch after that learn keys and after that learn ecu to learn ecu use xml(diagnostic running) thankyou brr but car take the long way to dealer sow i dont have chance to test. RE: Renolink Support/Feedback - otojm - 08-10-2019 hi, i'm newby with this sw, i don't understand what mean those mention :" Learning key in protected mode"??? also in tdb section :"only forward without pach"?? can someone explain for us, regards RE: Renolink Support/Feedback - otojm - 10-10-2019 (08-10-2019, 16:23 PM)otojm Wrote: hi, i'm newby with this sw, i don't understand what mean those mention :" Learning key in protected mode"??? no one ----------------- RE: Renolink Support/Feedback - otojm - 11-10-2019 hi, another issue: i have this UCH Réf: 8201068830 from Renault symbol 2007; i connect it with Renolink1.79>>uch_trans v7_1 but when i attempt to do" clear Immo Uch" it won't and give message:"can't clear immo" Regards RE: Renolink Support/Feedback - monini64 - 11-10-2019 i program second card in fluence 2017, works ok |