BMW BDC Bench Flashing - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61) +---- Thread: BMW BDC Bench Flashing (/showthread.php?tid=57133) |
BMW BDC Bench Flashing - paskuale - 28-09-2019 Hello mates, I'm trying to flash BMW BDC on the table. I connect BDC like in the picture I can diagnose BDC, read FA, read and calc SVT and TAL, but I can't flash it. When I try to flash, it start and then end with error after some seconds. I tried with ICOM and ENET, same result. Can someone help me, please ? Thank you Bests RE: BMW BDC Bench Flashing - krug - 28-09-2019 (28-09-2019, 11:21 AM)paskuale Wrote: Hello mates,This ☝ diagram for BMW explorer not icom. RE: BMW BDC Bench Flashing - paskuale - 28-09-2019 Can you help me with right diagram please ? I use this diagram with BMW-Explorer at table. RE: BMW BDC Bench Flashing - sameur10 - 28-09-2019 (28-09-2019, 11:21 AM)paskuale Wrote: Hello mates,Hi you can flash it if you can activate KL15 (ignition) with tool32 if you cant you need to activate it by KEY without KL15 flash wont go RE: BMW BDC Bench Flashing - paskuale - 28-09-2019 I don’t have key of this BDC, so I can’t activate KL15 by key. Can you explain me how to activate KL15 by Tool32, please ? Thank you Bests RE: BMW BDC Bench Flashing - RocketSurgeon - 29-09-2019 (28-09-2019, 22:35 PM)paskuale Wrote: I don’t have key of this BDC, so I can’t activate KL15 by key. Load fem.prg in tool32. Find the job steuern klemmen, and enter argument: KL15_EIN. RE: BMW BDC Bench Flashing - krug - 29-09-2019 I tried before with BDC and key, can't code or read FA, even BDC available in ista and tool 32 esys can't connect for some reason, I think something missing. RE: BMW BDC Bench Flashing - paskuale - 29-09-2019 (29-09-2019, 03:19 AM)RocketSurgeon Wrote:(28-09-2019, 22:35 PM)paskuale Wrote: I don’t have key of this BDC, so I can’t activate KL15 by key. I load BDC.prg because my ecu is BDC. I have always "Condition not correct" and KL15 is not powered on. I can power on any onther KL30 in the argument list. The only one not working is KL15. Any advice ? Thank you RE: BMW BDC Bench Flashing - paskuale - 05-10-2019 Nobody can help me with BDC bench flashing ? RE: BMW BDC Bench Flashing - Batje - 06-10-2019 (05-10-2019, 16:44 PM)paskuale Wrote: Nobody can help me with BDC bench flashing ? You need to have a valid key for the BDC on the emergency coil. If it gives you the conditions not correct error while executing the steuern klemme job it means it did not detect a valid key. |