[Problem] VTG X5 E70 4.8 - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61) +---- Thread: [Problem] VTG X5 E70 4.8 (/showthread.php?tid=58433) |
[Problem] VTG X5 E70 4.8 - Alekz - 24-10-2019 We just code the entire car with ISTA P (3.65) and when it finish, in VTG Module do the Promgram and goes check and then on Code gets the X... Finish other modules but no VTG, now the E70 X5 when starts get the 4x4, ABS, Traction Control, Parking lights and get this failures: Launch: 54C4 VTG 5F3A DSC 5F39 DSC The DTC can be cleared, but when i start the car they cames again... anyone can help me with this? Thanx! Alekz RE: [Problem] VTG X5 E70 4.8 - 2013m5 - 24-10-2019 (24-10-2019, 00:42 AM)Alekz Wrote: We just code the entire car with ISTA P (3.65) and when it finish, in VTG Module do the Promgram and goes check and then on Code gets the X... These faults for actuator gear worn out. Is clicking or clunking noise when engine turn off from the transfer case area? If yes, then the transfer case actuator gear worn out. You need the repair kit to rebuild transfer case actuator. Here is the P/N 27 10 2 413 711 Or you just buy after market gear. RE: [Problem] VTG X5 E70 4.8 - jaramillo - 24-10-2019 Try to flash the module via WinKFP, then code with Ncsexpert RE: [Problem] VTG X5 E70 4.8 - Alekz - 24-10-2019 I think that flash with WinKFP and code with ncsexpert is more viable... is there a way to do it with esys? Thanx! Alex RE: [Problem] VTG X5 E70 4.8 - BMWdriva - 24-10-2019 (24-10-2019, 13:45 PM)Alekz Wrote: I think that flash with WinKFP and code with ncsexpert is more viable... is there a way to do it with esys? hehe need to check tire pressure,before connecting the e-sys to the E-series. RE: [Problem] VTG X5 E70 4.8 - jaramillo - 24-10-2019 (24-10-2019, 14:37 PM)BMWdriva Wrote:(24-10-2019, 13:45 PM)Alekz Wrote: I think that flash with WinKFP and code with ncsexpert is more viable... is there a way to do it with esys? Not possible to work with E series in esys. RE: [Problem] VTG X5 E70 4.8 - BMWdriva - 24-10-2019 (24-10-2019, 15:27 PM)jaramillo Wrote:just a person does not understand what he is doing.(24-10-2019, 14:37 PM)BMWdriva Wrote:(24-10-2019, 13:45 PM)Alekz Wrote: I think that flash with WinKFP and code with ncsexpert is more viable... is there a way to do it with esys? RE: [Problem] VTG X5 E70 4.8 - Alekz - 24-10-2019 Thnx @jaramillo Gonna try with winkfp/ncsexpert RE: [Problem] VTG X5 E70 4.8 - carbumer - 24-10-2019 Just pull out the fuse and stand back and you will be happy RE: [Problem] VTG X5 E70 4.8 - jaki - 25-10-2019 (24-10-2019, 21:40 PM)carbumer Wrote: Just pull out the fuse and stand back and you will be happy Thumb up for that It is known problem that VTG module gets "broken" even after diagnostic. Battery reset helps for that. I have no idea what causes that problem. Anyway, cure is easy |