OP-COM 2020 FREE 4 ALL - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: Opel - Vauxhall - Holden (https://cartechnology.co.uk/forumdisplay.php?fid=59) +---- Thread: OP-COM 2020 FREE 4 ALL (/showthread.php?tid=58986) |
OP-COM 2020 FREE 4 ALL - fantomel - 13-01-2022 OP-COM 2020 MULTI VERSIONS FREE 4 ALL
Please read before you respond in topic and please provide some feedback. If you are curious open and see and you will not be sorry I always keep my word. And a little bit of help to see if your inteface is good or not. + I added down PDF's for CH-CAN modification and also if you like printed boards the project for it. Enjoy Fantomel RE: OP-COM 2020 FREE 4 ALL - fantomel - 16-01-2022 Revision C can manualy diag CH-CAN modules IMU, SAS, SADS, EPS. EPS - Elctronic Power Steering IMU - Multi-Axis Acceleration Sensor Module SAS - Steering Wheel Angle Sensor Module SADS - Suspension Control Module Cars with them: Adam - EPS Apera - IMU, SAS Astra J - IMU, SAS, SADS Cascada - IMU, SAS, SADS Corsa E - EPS Cruze - SAS Karl/Viva - EPS Mokka - IMU, SAS Insignia - SAS, SADS Zafira C - SAS, SADS Since i forgot to add this info. You will not find them on autodetect but you can enter on them manualy. Also because i was asked here is a real picture of a genuine V5 interface, not fakes. RE: OP-COM 2020 FREE 4 ALL - bigf7o - 21-03-2022 Hy i have one op-com clone i have try all whit him buth dont i have connection whit auto only (please whait ,to the test interface is recognized and ok ...buth stil not work)there is a possibility to do something whit him ...... thank you very much RE: OP-COM 2020 FREE 4 ALL - mattydr67 - 22-03-2022 (21-03-2022, 15:36 PM)bigf7o Wrote: Hy i have one op-com clone i have try all whit him buth dont i have connection whit auto only (please whait ,to the test interface is recognized and ok ...buth stil not work)there is a possibility to do something whit him ...... thank you very muchYou have a fake MCU In your PCB you have to remove C11 and replace the MCU with a real/original one and you have to flash it using an external PIC programming. Check here OP-COM v6 with "fake MCU" REPAIR (cartechnology.co.uk) Good luck RE: OP-COM 2020 FREE 4 ALL - yayaasd - 28-03-2022 wow - great work fantomel!! I am just wondering if this PCB will work - see attachment RE: OP-COM 2020 FREE 4 ALL - bersch8688 - 28-03-2022 (28-03-2022, 12:03 PM)yayaasd Wrote: wow - great work fantomel!! Open your Eye's! Check the Picture from Fantomel!!! RE: OP-COM 2020 FREE 4 ALL - yayaasd - 28-03-2022 (28-03-2022, 12:24 PM)bersch8688 Wrote:(28-03-2022, 12:03 PM)yayaasd Wrote: wow - great work fantomel!! I did now again, thank you for clarifying. seems that I have an fake pcb. RE: OP-COM 2020 FREE 4 ALL - justdiag - 28-03-2022 As i remember in another forum a user put the PCB modification to revision C with BC847 and provided also the layout board (see attach) And for this to be complete before the "reset" there was a modification done to OP-COM NEW PCB by a user who said that you need to cut a trace on the back of PCB then you need to to the same tutorial as the one for V5. (see picture bellow , don't mind the wire) Keep in mind these infos are colected over time and i did not test them. RE: OP-COM 2020 FREE 4 ALL - justdiag - 28-03-2022 Oups , clumsy me ...... i forgot about this one below , for those that are not in the mood of making one or don't find in china one good clone to modify and don't mind to spend 60$ i found this picture from a friend And by looking around i found out that you can buy this interface in the link from attachment. case RE: OP-COM 2020 FREE 4 ALL - mattydr67 - 29-03-2022 Just for your information: This is the last 1:1 original OP-COM Advanced hardware Revision D+ Good luck |