+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: Solved ✔ F10 NBT evo retrofit side view cameras not working (/showthread.php?tid=60550)
Pages:
1
2
F10 NBT evo retrofit side view cameras not working - egoy936 - 12-02-2022
Hello everyone,
I just retrofitted a NBT evo into my 2016 f10 with factory surround view. However sideview is not working shown in the photo below. I have confirmed 3AG and 5DL are part of the VO and factory coded it with this VO.
Suspect I need to FDL code something but I am unsure of what! Any help would be must appreciated.
RE: F10 NBT evo retrofit side view cameras not working - egoy936 - 13-02-2022
Bump?? Anyone have a f06 NBT EVO with surround view NCD file?
RE: F10 NBT evo retrofit side view cameras not working - maxwell4321 - 13-02-2022
Here you go but I have to ask have you checked the car with ISTA, it may just need camera calibration. Also VO code TRSVC.
RE: F10 NBT evo retrofit side view cameras not working - egoy936 - 16-02-2022
(13-02-2022, 06:54 AM)maxwell4321 Wrote: Here you go but I have to ask have you checked the car with ISTA, it may just need camera calibration. Also VO code TRSVC.
I tried all that and still will not work. I even tried a different TRVSC module. Same issue and the below error
800BA9 TRSVC CVBS Output, short circuit
Any ideas?
RE: F10 NBT evo retrofit side view cameras not working - DayvG - 16-02-2022
(16-02-2022, 22:24 PM)egoy936 Wrote:Check your FBAS connection to the HU? Is it only top view cameras not working? Does rear cam work?(13-02-2022, 06:54 AM)maxwell4321 Wrote: Here you go but I have to ask have you checked the car with ISTA, it may just need camera calibration. Also VO code TRSVC.
I tried all that and still will not work. I even tried a different TRVSC module. Same issue and the below error
800BA9 TRSVC CVBS Output, short circuit
Any ideas?
Attached is my CAFD from my F10 with NBT EVO including surround view.
RE: F10 NBT evo retrofit side view cameras not working - Jhnblckwood - 16-02-2022
HU_NBT > 3001 > CAMERA_SYSTEM = trsvc
RE: F10 NBT evo retrofit side view cameras not working - ga3 - 17-02-2022
Is the HSD wire genuine?
If you use non-genuine HSD wire, the pin assignment may be different.
I recommend checking with a tester.
RE: F10 NBT evo retrofit side view cameras not working - egoy936 - 17-02-2022
(16-02-2022, 22:43 PM)DayvG Wrote:(16-02-2022, 22:24 PM)egoy936 Wrote:Check your FBAS connection to the HU? Is it only top view cameras not working? Does rear cam work?(13-02-2022, 06:54 AM)maxwell4321 Wrote: Here you go but I have to ask have you checked the car with ISTA, it may just need camera calibration. Also VO code TRSVC.
I tried all that and still will not work. I even tried a different TRVSC module. Same issue and the below error
800BA9 TRSVC CVBS Output, short circuit
Any ideas?
Attached is my CAFD from my F10 with NBT EVO including surround view.
Only Rear view camera works but still shows error on dash. Top view does not
(17-02-2022, 00:34 AM)ga3 Wrote: Is the HSD wire genuine?
If you use non-genuine HSD wire, the pin assignment may be different.
I recommend checking with a tester.
I am using a quadlock harness with an activator. I wonder if this is the issue.
RE: F10 NBT evo retrofit side view cameras not working - ga3 - 17-02-2022
HSD wire is an LVDS 4-core wire between the camera and controller.
*edit
Oops, it was the factory 5DL...shouldn't be a problem just because I changed to EVO...
RE: F10 NBT evo retrofit side view cameras not working - maxwell4321 - 17-02-2022
The fact that your error says Short circuit points to incorrect wiring on your quadlock harness, check that the video cable pins from TRSVC are on 21(+),24 (-)and 23 (shield)at the EVO (could also be on pins 18(+) 28(-) 27(Shield).
Also you have to tell the EVO in the CAF which pins it is connected to, there is a werte value that needs setting. search caf for camera and find CAM ECU then set the werte value for Top/Side view to werte_01 (may need a different number if your video feed is on different pins)