AUDI CAN GATWAY 8w7907468 Help - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: VAG Group (VW - Audi - Seat - Skoda - Bentley) (https://cartechnology.co.uk/forumdisplay.php?fid=55) +---- Thread: AUDI CAN GATWAY 8w7907468 Help (/showthread.php?tid=63551) Pages:
1
2
|
AUDI CAN GATWAY 8w7907468 Help - hana - 20-04-2022 When I used ODIS Engineering 9.2.2 to flash the module address 19 "can gateway" , the flashing went to 93% then stopped and showed error , the ignition wont turn on now. note: only the CAN Gateway module can communicate with the diagnostic tool, all other modules have no communication, i believe the Can Gateway module is stuck in boot mode. I would appreciate it if anyone has an idea how to reflash this module without error.... by the way i used "8W7 907 468 H11 2079"for reflashing see below the module details Address 19: CAN Gateway (J533) Labels:* None Part No SW: 8W7 907 468 HW: 8W7 907 468 Component: Gateway H11 2079 Revision: 3M130039 Serial number: 3983M050016227 Coding: 0301000100000F407F070000005900324C920007080000000175078E00000000 Shop #: WSC 31414 790 00001 GVL: 01503C0408040000C0BC08000002C80001080000000000000000000000000000 ASAM Dataset: EV_CGateCONTIAU491 002040 ROD: EV_CGateCONTIAU491_002_AU49.rod VCID: 0814669AB38D3FCF82-805C RE: AUDI CAN GATWAY 8w7907468 Help - Tekero - 21-04-2022 What is original HW/SW and name of file which you trying to flash RE: AUDI CAN GATWAY 8w7907468 Help - hana - 22-04-2022 the original HW/SW is H11 2079 and i use the same flash " FL_8W7907468_2079___S.frf" i use odis E 9.2.2 and 14.1 , in both the flashing stop at 93% the give me error the details of my original module in below Address 19: CAN Gateway (J533) Labels:* None Part No SW: 8W7 907 468 HW: 8W7 907 468 Component: Gateway H11 2079 Revision: 3M130039 Serial number: 3983M050016227 Coding: 0301000100000F407F070000005900324C920007080000000175078E00000000 Shop #: WSC 31414 790 00001 GVL: 01503C0408040000C0BC08000002C80001080000000000000000000000000000 ASAM Dataset: EV_CGateCONTIAU491 002040 ROD: EV_CGateCONTIAU491_002_AU49.rod VCID: 0814669AB38D3FCF82-805C RE: AUDI CAN GATWAY 8w7907468 Help - Tekero - 23-04-2022 what file did you flash 1st time when you got error? RE: AUDI CAN GATWAY 8w7907468 Help - hana - 23-04-2022 i told you bro, I flash the module with the same number "FL_8W7907468_2079___S.frf" i didnt used diffrent flash... DOES ANYONE HAVE THE PIN CONNECTION FOR THE PROCCESSOR SPC5646, THE VVDI PRO CAN READ THIS CHIP , BUT I NEED HELP FOR HOW TO CONNECT RE: AUDI CAN GATWAY 8w7907468 Help - Tekero - 24-04-2022 Why did you flash this module with same version? what profit? try this file RE: AUDI CAN GATWAY 8w7907468 Help - hana - 24-04-2022 i was have an issue with both TPMS and Parking Aid " no communication " and i was tried the coding also , but not fixed , that's why i tried to reflash the GW module to double check , but unfortunately the car stopped to run now and there is now no communication with all modules in the car. but i didnt use your flash , but i used "FL_8W7907468_2079___S.frf" RE: AUDI CAN GATWAY 8w7907468 Help - mrbla - 25-04-2022 2079 is pretty old software. Normally opening car, connecting to obd and flashing should be enough. There is no need for ignition on or so to flash it. However there is a tsb especially for the old ones. Also had the luck to brick one of a friend In the TSB they hint to exchange the old once. You can try to reflash. Even newer like 7079 should work. I wouldn’t use 01xx, 02xx, 03xx. They are properly too new for this ecu hw. RE: AUDI CAN GATWAY 8w7907468 Help - hana - 26-04-2022 thanks mrbla, i will try to reflash with FL_8W7907468_8079___S.frf, also tomorrow i will get a second hand used module 8W7907468E and i know this module dont have e-call , but i will test on the car , at lest to make the car running again then make the coding. so do you think the used module will not need any other steps like "programming, immoblizing or component protection" RE: AUDI CAN GATWAY 8w7907468 Help - hana - 26-04-2022 i tried to reflash , its same resualt , the flashing stop at 93% then occure error , see the log file |