Icom Next A issue - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61) +---- Thread: Icom Next A issue (/showthread.php?tid=63618) Pages:
1
2
|
Icom Next A issue - vld - 21-04-2022 Hello, I have an ICOM NEXT original that can't read E83 3.0d '06, why is this due to the fact that there is no support for the K line? I used to have an ICOM A2 clone and I never had to build a bridge between 7 and 8 pins and now ICOM NEXT did not want to read any module and did not identify the car at all until I made a 7 and 8 pin bridge. Do you have any idea why this is so? The firmware of ICOM NEX is FW_03-15-08 ISTA Standalone 4.34.4x Any help will be helpful. RE: Icom Next A issue - Bimmer540 - 21-04-2022 Can you post picture from itoolradar fw next RE: Icom Next A issue - vld - 21-04-2022 (21-04-2022, 20:18 PM)Bimmer540 Wrote: Can you post picture from itoolradar fw next I can, but tomorrow it will be too late to go down to the garage again. RE: Icom Next A issue - Bimmer540 - 21-04-2022 Try BMW_ISPI_ICOM-FW_03-22-11.msi RE: Icom Next A issue - Node - 21-04-2022 ICOM Next should read all BMW cars. If it can't then either it's faulty or there is something wrong with a car. RE: Icom Next A issue - ferrum - 22-04-2022 It is faulty, there is no switching on pin 8 and most likely one of the 393 is faulty RE: Icom Next A issue - vld - 22-04-2022 (22-04-2022, 00:39 AM) ferrum Wrote: It is faulty, there is no switching on pin 8 and most likely one of the 393 is faulty Hi, I enclose a few screenshots and logs of the device, if anything more can be understood from them. The device test passes without error. If there is a defective element on the motherboard, I hope to replace it without additional conditions, it was purchased from a company distributor of OEM parts. RE: Icom Next A issue - stefankrol - 22-04-2022 What are your settings in ISTA? RE: Icom Next A issue - vld - 22-04-2022 (22-04-2022, 12:28 PM)stefankrol Wrote: What are your settings in ISTA? I have no problem with the connection to vehicles set up on a local network with DHCP of ICOM. I have diagnosed and programmed dozens of E9x / E6x / E7x / F10 / F30 and so on. There is a problem specifically with the connection to the old E46 / E39 / E53 / E83. And since until recently I used an ICOM A2 clone with which I had no problems connecting to any car, now I expected the same from ICOM NEXT A. I have had it for a month and only now I had to inspect such a car and accordingly I realized that there is a problem. RE: Icom Next A issue - Bimmer540 - 22-04-2022 When you connect old E46 / E39 / E53 / E83, you must give in first full vin and then connect to car... |