Solved ✔ E38 93s66 IKE mileage - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10) +--- Thread: Solved ✔ E38 93s66 IKE mileage (/showthread.php?tid=67093) Pages:
1
2
|
E38 93s66 IKE mileage - lustek - 26-07-2022 Hi, After battery drain instrument cluster and EWS show 999999 km. I correct mileage on EWS but need help with IKE. Eeprom dump in atachement. I already try pasoft mileage correction tool but no luck. Dont want to disassembly ike because od needles. Maybe if I have correct dump, with correct mileage I can try just write eeprom - what you thing? Could somebody correct for me this dump with propper mileage? Even in case when I need to write to blank eeprom - just want to write, assemby everything back and done Now mileage show all 9 and have fault in IKE aboute wrong checksum Dest. mileage - 339300 Thank you RE: E38 93s66 IKE mileage - Vojno - 26-07-2022 If in the IKE not 35080 eprom has and you have PA soft, then you need one signalgenerator witch can make maybe 200Hz Then this signal connect for the speed pin and use the PA soft. RE: E38 93s66 IKE mileage - lustek - 26-07-2022 (26-07-2022, 18:09 PM)Vojno Wrote: If in the IKE not 35080 eprom has and you have PA soft, then you need one signalgenerator witch can make maybe 200Hz Thank you. Could you write more information aboute this signal generator? From where I can get one This one will be fine? RE: E38 93s66 IKE mileage - Vojno - 27-07-2022 This is mor then enoug! if the output signal is 12V I use that one: The BNC negative connect to the car negative (GND) and the signal (hotspot) to the "Speed signal" pin+ Depend on which kind of type: LOW or HIGH (CC) two or three connector, see pictures: RE: E38 93s66 IKE mileage - lustek - 27-07-2022 I think this generator dont have 12V on output so I need to found else. What kind of signal it should generate? squer or sin? or no mater? (27-07-2022, 08:34 AM)lustek Wrote: I think this generator dont have 12V on output so I need to found else. OK, no matter. I saw you atachement with proper generator RE: E38 93s66 IKE mileage - Vojno - 27-07-2022 Squer and 50% is ok. But I don't think it's sensitive to the fill factor (duty cycle) If you dont have 12V output then you need one transistor and two resistor to make open collector output foryour signal generator. like this: RE: E38 93s66 IKE mileage - lustek - 27-07-2022 (27-07-2022, 08:37 AM)Vojno Wrote: Squer and 50% is ok. But I don't think it's sensitive to the fill factor (duty cycle) Man, you are BOSS thank you very much. I bought same generator as you post so I dont need to make open collector. So, mileage could be write when on dash will be 2 km/h or 200 km/h? I found different information on different source RE: E38 93s66 IKE mileage - Vojno - 27-07-2022 I don't remember exactly anymore but in PA soft in the KOMBI you have menu for the mileage correction where it asks for the exact value valuewhat you want to see. It also says to connect the speed signal there also the required frequency. Then you see the mileage is go up (slowly) And maybe 1-2 minutes as if make a reset and the KOMBI switch off and on and tadam! RE: E38 93s66 IKE mileage - lustek - 27-07-2022 (27-07-2022, 09:34 AM)Vojno Wrote: I don't remember exactly anymore but in PA soft in the KOMBI you have menu for the mileage correction where it asks for the exact value valuewhat you want to see. Yes but in my case, mileage not go UP because I have all 999999. OK, will try and report when signal generator arrived RE: E38 93s66 IKE mileage - Vojno - 27-07-2022 It doesn't matter if you want up or down. |