FRM Bench Test - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: IMMO & LOCKSMITH (https://cartechnology.co.uk/forumdisplay.php?fid=9) +--- Thread: FRM Bench Test (/showthread.php?tid=70005) |
FRM Bench Test - DaBotta - 08-10-2022 Hello I want to make an test bench cable , so i can program and test frm directlyy on bench. I have aJBFE from E9x , obd socket , but i don't know , exactly the wires that need to connect the obd connector. I saw that from JBFE to FRM i need to connect the CAN wires , but from JBFE to OBD how do i connect them ? Someone have an schematic ? Thank you RE: FRM Bench Test - screwdriver - 08-10-2022 Here you go for programming the FRM with VVDI PROG xxxxxxxxxxxxxxxxxxxxxxxxxx RE: FRM Bench Test - DaBotta - 08-10-2022 (08-10-2022, 11:36 AM)screwdriver Wrote: Here you go for programming the FRM with VVDI PROG You didn't understand. Need them for coding , programing on bench. Not to write eeprom or flash. I have what you showed here , this is for repair FRM3 RE: FRM Bench Test - Arthur_79 - 08-10-2022 (08-10-2022, 11:16 AM)DaBotta Wrote: Hello Is this OK? RE: FRM Bench Test - DaBotta - 08-10-2022 (08-10-2022, 11:59 AM)Arthur_79 Wrote:(08-10-2022, 11:16 AM)DaBotta Wrote: Hello Hello , i saw the newtis diagram , but i think JBBFE don't have that K Can connector , only CAN Low and High , those one cannot connect directly to obd , right ? Need some different can transformer ? RE: FRM Bench Test - Arthur_79 - 08-10-2022 (08-10-2022, 12:18 PM)DaBotta Wrote:(08-10-2022, 11:59 AM)Arthur_79 Wrote:(08-10-2022, 11:16 AM)DaBotta Wrote: Hello CAN Low and High connect directly to obd socket. No need CAN transformer. RE: FRM Bench Test - Spitfire555 - 10-10-2022 The JBE (built into the JBBF) is the gateway. The gateway has all(!) available connections, also to OBD connector with D-CAN (500kBit/sec) / K-Line, also to K-CAN (100kBit/sec). RE: FRM Bench Test - DaBotta - 14-10-2022 Tried all the wiring , and NO RESPONSE FROM CONTROL UNIT . What i am doing wrong .... FRM X14261 Pin 12 Wake Up -> 12V X14260 Pin 43 PT CAN_L -> JBE PIN 2 Blue Socket X14260 Pin 44 PT_CAN_H -> JBE PIN 1 Blue Socket X14260 Pin 45 K_CAN_l -> JBE PIN 10 Blue Socket X14260 Pin 46 K_can_H -> JBE PIN 46 Blue Socket All the powers and wake up for both modules OBD Tried even PIN 33 to PIN 7 OBD D_TXD1 and even PIN 33 D_CAN_L to PIN 14 OBD and PIN 17 D_CAN_H to PIN 6 OBD Same result. The JBE is from 2008 / 09 What i am doing wrong ? |