[RESTARTED] icom next clone repair (only single pcb) - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61) +---- Thread: [RESTARTED] icom next clone repair (only single pcb) (/showthread.php?tid=73571) |
[RESTARTED] icom next clone repair (only single pcb) - ____ANGEL___ - 08-01-2023 I want to restart a thread that was lost after the db recovery. These informations belongs to Ferrum, it's not my work. May this can be useful to someone that has a icom clone single pcb version, this thread is only related to icom with single pcb. If Ferrum would like to give suggestions here i'd be really happy. Due to wrong assebly by chinese production, check all this: swap R292<->R293 R155<->R156 R178<->R179 check or change R15 52ohm R119 1k R280 R285 R195 38k Y4 33000 3.3v R233 62k (r233 can be left unchanged. R233 installed 47k and should be 62k but this is not critical) R178 100k R179 1.4k R156 72ohm R292 72ohm R155 1K R293 1K other infos in attachments. RE: [RESTARTED] icom next clone repair (only single pcb) - ferrum - 09-01-2023 Now in the Chinese market, 3 varieties are sold with different errors. Only one R119 error is repeated in all clones. There are clones in which the quartz is set at the correct frequency of 33000 but it has other critical errors. Not everyone needs to change places R292<->R293 R155<->R156 Not everyone needs R15 52ohm Y4 33000 3.3v Some added other errors that are not described here. If your icom board has R15 52ohm then this guide does not fully address the fixes that need to be done RE: [RESTARTED] icom next clone repair (only single pcb) - MIKUr1 - 06-02-2023 Small PCB with switch must be done by me to make ICOM restore? RE: [RESTARTED] icom next clone repair (only single pcb) - rayeton - 06-02-2023 (06-02-2023, 14:01 PM) MIKUr1 Wrote: Small PCB with switch must be done by me to make ICOM restore? Yes, you are right. RE: [RESTARTED] icom next clone repair (only single pcb) - ferrum - 06-02-2023 The restore function is extremely rarely needed, since in most cases it is associated with the repair and replacement of microcircuits. I don't install the board and only use it when I need it. If you need a restore button, I drew a diagram that is understandable even to a non-repair specialist and it is quite easy to reproduce it. The contact going to the LM77 is a connection with 3.2v, it can be taken from another place. Difficulties may arise when soldering to the 42nd leg of the mega16 and this must be done very carefully without damaging the microcircuit, since in the event of a breakdown, the mega16 can only be taken from the donor RE: [RESTARTED] icom next clone repair (only single pcb) - MIKUr1 - 06-02-2023 Rarely needed, but without serial change and restore, ICOM will give fan error, am I right? RE: [RESTARTED] icom next clone repair (only single pcb) - ferrum - 06-02-2023 The button can be connected neatly without a bunch of wires I make these wires myself, they fit clones and originals RE: [RESTARTED] icom next clone repair (only single pcb) - MIKUr1 - 07-02-2023 One more question - I saw that some ICOM NEXT's have some cheaper versions, without one of port's - the round one with 5 pins. What is purpose of this port? There is no matching cable for it. RE: [RESTARTED] icom next clone repair (only single pcb) - ____ANGEL___ - 07-02-2023 Imib oscilloscope RE: [RESTARTED] icom next clone repair (only single pcb) - MIKUr1 - 07-02-2023 So I assume, that this port is not neccessary? Or there is some more differences? |