All Repairs PSA XS EVOLUTION interface !

All Repairs PSA XS EVOLUTION interface ! - Printable Version

+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: PSA Group (Citroen - Peugeot) (https://cartechnology.co.uk/forumdisplay.php?fid=56)
+---- Thread: All Repairs PSA XS EVOLUTION interface ! (/showthread.php?tid=7456)

All Repairs PSA XS EVOLUTION interface ! - titoun - 28-05-2015

Hi,

Here is face down (LED side) of five microprocessor electronics boards of XS EVOLUTION interfaces.

[Image: 5_cart10.jpg]

Two of them, in this case the two electronic boards to the left in the photo above,
have communication problems on CAN bus, and particularly on FULL CAN vehicles.
These two cards out:

[Image: deux_c10.jpg]

The three others, here, do not have this concern:

[Image: 3_cart10.jpg]

When you look carefully at the two cards down, one perceives a missing component here:

[Image: manque10.jpg]

This is a 10Kohms resistor (marking 103); PULL UP resistor placed on the CAN line that comes
the PIN P94 / TXO microprocessor MB90F546GS and then passes through the logic of HA08 before reaching the optocoupler HCPL 063N!

[Image: microp10.jpg]

So if you have CAN communication problems with your interfaces, you can already take a look to see if this resistance is present!
Pending your back ...

Regards.

All Repairs PSA XS EVOLUTION interface ! - Michael1 - 04-02-2018

Hi
Please help
I have problem with Lexia interface, normallly it worked, during the reinstallation of DiagBox installed driver OK Led light normal but after that the interfacve is dead, I tried repleace USB cable, nothing, open iterface an measure conecting, cable and VGA conecor are good, interface have +5 V and grund through USB, D+ and D- from USB passing through small chip?? maybe that this is prblem ? here is 6 pin, there is small resistance (cca 20 ohm) measured betwen pin 1 - 6 and 3 -4 , that is maybe OK if it is noise filter? but i am not sure.
Thanks in advance
Best Regards Michael

RE: All Repairs PSA XS EVOLUTION interface ! - titoun - 18-02-2018

Hi,

ESD suppressors : ref USBUF01W6
Marking code UU1

B.regards

RE: All Repairs PSA XS EVOLUTION interface ! - Michael1 - 18-02-2018

Hi
When I connect the interfacco to the USB laptop does not see it, LED notlight, have you any idea where is problem?
Thanks in advance
best regards Michael

RE: All Repairs PSA XS EVOLUTION interface ! - titoun - 18-02-2018

Maybe microprocessor MB90F546GS is bricked... ? try an hardware reflash of this!

B.regards

RE: All Repairs PSA XS EVOLUTION interface ! - andy_sim1 - 24-06-2018

Good Morning,
I have just been updating the firmware with Scary interface tool, during update cable got unplugged, and now the unit fails to respond. Green light is on but Scary's interface checker does not show anything.
Is it possible to re-flash using another way?
any help appreciated.
Thank you.

Best regards
Andy

RE: All Repairs PSA XS EVOLUTION interface ! - cro1983 - 09-11-2018

I have same problem, how can i do hardware reflash?

(18-02-2018, 16:48 PM)Michael1 Wrote: Hi
When I connect the interfacco to the USB laptop does not see it, LED notlight, have you any idea where is problem?
Thanks in advance
best regards Michael

RE: All Repairs PSA XS EVOLUTION interface ! - km666 - 29-10-2022

Hi
I have problem Peugeot 206 (2002 year) no communication with engine ECU.Other module communication is the ok.
I found an l-line problem.Pin 15 has constant 12V.It used to work fine
Any idea?

RE: All Repairs PSA XS EVOLUTION interface ! - MORKAS - 27-03-2023

Greetings @titoun, and thanks for the post. In my case, the problem I have is that they flashed the VCI, and they have changed the serial number (it had 921815C, and after flashing it now it has 963830C, which for the latest versions of diagbox, it seems that o OK). Since then, when I start Diagbox, and try to connect to the vehicle (the first time, after changing firmware to test, update the interface), it does not read the VIN of the vehicle and does not even "click" the VCI relays. In the photos in your post, I see that there is one that matches mine, that is, it does not have that resistance, but, of course, I do not know if it is due to that, or that perhaps the VCI has become useless when changing the number of series....thank you...