+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: Add the ICM unit to bench setup (/showthread.php?tid=82910)
Add the ICM unit to bench setup - Haug530d - 04-09-2023
I want to add the ICM unit to my benchsetup for the NBT.
So is this the correct setup for that?
No3 on ICM to 32 on ZGW
No4 on ICM to 33 on ZGW
And
Power to no 18 on Icm
and Earth to no 34 on Icm
At least this is what i could read out of the Wiring Scheme from the ICM on TIS.
And Yes, it is an LCI Unit.
RE: Add the ICM unit to bench setup - DEJMIEN - 04-09-2023
You don’t need ICM to get headunit working on the bench. ZGW, ZBE and any wake-up device it’s enough to get the heading working on the bench.
RE: Add the ICM unit to bench setup - user_530d - 04-09-2023
ICM don't work on bench without other FlexRay ECU like DSC2
RE: Add the ICM unit to bench setup - Haug530d - 04-09-2023
(04-09-2023, 08:33 AM)DEJMIEN Wrote: You don’t need ICM to get headunit working on the bench. ZGW, ZBE and any wake-up device it’s enough to get the heading working on the bench.
I Already have the headunit working on bench, i just wanted to flash it before car installation.
(04-09-2023, 09:48 AM)user_530d Wrote: ICM don't work on bench without other FlexRay ECU like DSC2
ah ok, thanks, guess i'll just install it in the car then.
RE: Add the ICM unit to bench setup - DEJMIEN - 04-09-2023
(04-09-2023, 09:50 AM)Haug530d Wrote:(04-09-2023, 08:33 AM)DEJMIEN Wrote: You don’t need ICM to get headunit working on the bench. ZGW, ZBE and any wake-up device it’s enough to get the heading working on the bench.
I Already have the headunit working on bench, i just wanted to flash it before car installation.
(04-09-2023, 09:48 AM)user_530d Wrote: ICM don't work on bench without other FlexRay ECU like DSC2
ah ok, thanks, guess i'll just install it in the car then.
You can flash NBT if you have ZGW rewired correctly.
Do you want to flash something else?
RE: Add the ICM unit to bench setup - VroomVroom - 04-09-2023
my setup to flash/diagnose nbt or nbt evo:
1) network setting on PC 169.254.199.77
2) direct connection lan cable to HU (+12v to EthA on HU)
3) elm327 can wires 7/14 pin to can pin on HU
4) power on elm and using extratool on android (kl 15 simulator adapter) sent CAN message to HU
5) to program HU using in Esys gateway connection 169.254.199.99:6801
6) to diagnose HU using Tool32 in Ediabas.ini use Enet connection and instead Autodetect use 169.254.199.99
RE: Add the ICM unit to bench setup - Haug530d - 04-09-2023
(04-09-2023, 10:53 AM)DEJMIEN Wrote:(04-09-2023, 09:50 AM)Haug530d Wrote:(04-09-2023, 08:33 AM)DEJMIEN Wrote: You don’t need ICM to get headunit working on the bench. ZGW, ZBE and any wake-up device it’s enough to get the heading working on the bench.
I Already have the headunit working on bench, i just wanted to flash it before car installation.
(04-09-2023, 09:48 AM)user_530d Wrote: ICM don't work on bench without other FlexRay ECU like DSC2
ah ok, thanks, guess i'll just install it in the car then.
You can flash NBT if you have ZGW rewired correctly.
Do you want to flash something else?
I said i already have a working Bench setup, with NBT ZGW and ZBE.
I have already flashed 2 NBT units and made one ZGW 02-mid to ZGW2 4SK.
and im putting the NBT,ZBE,ICM and a ZGW 8SK into my Pre-Facelift F11, i just wanted to Flash the ISM before i installed it in the car, but i can also flash it inside the car, no problem.
I'm also making a harness for the Facelift ICM, so that everything is reversible.
(04-09-2023, 17:00 PM)VroomVroom Wrote: my setup to flash/diagnose nbt or nbt evo:
1) network setting on PC 169.254.199.77
2) direct connection lan cable to HU (+12v to EthA on HU)
3) elm327 can wires 7/14 pin to can pin on HU
4) power on elm and using extratool on android (kl 15 simulator adapter) sent CAN message to HU
5) to program HU using in Esys gateway connection 169.254.199.99:6801
6) to diagnose HU using Tool32 in Ediabas.ini use Enet connection and instead Autodetect use 169.254.199.99
I bought cables and simulator box on Ebay (From Bimmer8) and connection goes trough my router, so i can choose between one of my 5 computers to connect to the Bench setup.