FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3) +--- Forum: CHIPTUNING (https://cartechnology.co.uk/forumdisplay.php?fid=12) +--- Thread: FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 (/showthread.php?tid=8474) |
FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - fantomel - 28-06-2015 FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 What you can find here: 1.For tool number 0386: ept file,fix file,hex dump and 2 versions of programs V54 used for it, the one from china and the AES November software. 2.For tool number 0475: ept file,fix file, hex dumps made from my tool and program V54 for it that does not need time back. 3.For both tools you have here how to connect to it, how to read firmware movie, how to write dump that you wish. Reading and writing the mcu for this tool can be done with old Philips LPC 2000 software and USB-TTL adapter, preferd the one that uses PL2303 chipset. You need also a jumper in position to do that. If you want to check CRP level of your NXP LPC2119 mcu you can do that with FlashMagic and USB-TTL adapter. Password: fantomelfree4galletto Enjoy. RE: FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - ToNy68 - 02-07-2015 Hello, Can I use it with v53 ? thank you RE: FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - blacklisted - 02-07-2015 Only v54 with the above serials RE: FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - rs@chip - 03-07-2015 What is the diferents betwen china and AES for 0386 number ? are this better softs and dumps than ori-ones which came with v54 china? RE: FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - fantomel - 04-07-2015 Aes and china uses same key for v54 witch in fact is older version of soft and bootlloader then 0475. RE: FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - rs@chip - 05-07-2015 Are there any eprovment if reflash..my v54 cant read a lot of ecu on can-bus and bdm RE: FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - fantomel - 08-07-2015 The question is how is your reworked board? Is it or is it not? is it proper or not ....... it does not matter only fw+soft you know .... RE: FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - rs@chip - 09-07-2015 I didnt rework anything yet..I have problems with can-line and bdm mpc55xx 56xx..k-line works..can you tel me which part need to be replaced to make this work?thanks.. RE: FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - toms4 - 09-07-2015 For BDM change 74HC14, and resolder noncorrectly soldered pins on pcb (relays) CAN issue can be 82C250 RE: FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386 - rs@chip - 09-07-2015 Thank you for that info ..noncorectly soldered pins..you meen relays? |