+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310)
+--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40)
+---- Forum: BMW - Mini - Rolls Royce (https://cartechnology.co.uk/forumdisplay.php?fid=61)
+---- Thread: NBT Evo bench test can not ping (/showthread.php?tid=86188)
NBT Evo bench test can not ping - alsamaraee - 03-12-2023
Hi,
I have a Nbt Evo HW 4.1 connected to a ZGW 4sk(2x Ethernet ports) via OABR connector. I'm using a can bus board to send ignition and vin signal to wake both ZGW and HU.
ZGW OABR
--------------------------------
11--------TX+ ----------17
12--------TX- ---------- 19
9 ---------RX+ ---------18
18--------RX- -----------20
Screen is on, can see both on e-sys. Can code HU.
My problem is that HU ethernet is not working. if I try to ping 169.254.199.99 it says host unreachable. And of cource it is not possible to flash the HU.
Tried connect OABR to rj45 and the ip 169.254.199.99 is presented in my network and able to ping the ip.
Of course HU ethernet is disconnected from ZGW side though.
RJ45 OABR
--------------------------------
1--------TX+ ----------17
2--------TX- ---------- 19
3--------RX+ ---------18
6--------RX- -----------20
Do I missing something?
Thanks in advance
RE: NBT Evo bench test can not ping - naderlouis - 03-12-2023
Attach a picture of which connector in the ZGW
RE: NBT Evo bench test can not ping - alsamaraee - 03-12-2023
(03-12-2023, 17:24 PM)naderlouis Wrote: Attach a picture of which connector in the ZGW
RE: NBT Evo bench test can not ping - walkernight88 - 03-12-2023
(03-12-2023, 15:25 PM)alsamaraee Wrote: Hi,
I have a Nbt Evo HW 4.1 connected to a ZGW 4sk(2x Ethernet ports) via OABR connector. I'm using a can bus board to send ignition and vin signal to wake both ZGW and HU.
ZGW OABR
--------------------------------
11--------TX+ ----------17
12--------TX- ---------- 19
9 ---------RX+ ---------18
18--------RX- -----------20
Screen is on, can see both on e-sys. Can code HU.
My problem is that HU ethernet is not working. if I try to ping 169.254.199.99 it says host unreachable. And of cource it is not possible to flash the HU.
Tried connect OABR to rj45 and the ip 169.254.199.99 is presented in my network and able to ping the ip.
Of course HU ethernet is disconnected from ZGW side though.
RJ45 OABR
--------------------------------
1--------TX+ ----------17
2--------TX- ---------- 19
3--------RX+ ---------18
6--------RX- -----------20
Do I missing something?
Thanks in advance
Had the same issue with ZGW Mid flashed to 4SK. Once I've used High flashed to 8SK, issue went away. Somehow ZGW doesn't route ethernet HU side. Didn't care to look much into it as I had 2-3 zgws laying around..
Use tool32 and run zgw01.prg -> STATUS_ETHERNET_INFORMATION
Post the output
RE: NBT Evo bench test can not ping - alsamaraee - 03-12-2023
Hello walkernight88,
Here it is
---------------------------------------------------------------------
apiJob("ZGW_01","status_ethernet_information","","")
Satz : 0
OBJECT = zgw_01
SAETZE = 1
JOBNAME = status_ethernet_information
VARIANTE = ZGW_01
JOBSTATUS =
UBATTCURRENT = -1
UBATTHISTORY = -1
IGNITIONCURRENT = -1
IGNITIONHISTORY = -1
Satz : 1
STAT_OBD_AKTIVIERUNGSLEITUNG = 1 01 .
STAT_OBD_AKTIVIERUNGSLEITUNG_TEXT = OBD Aktivierungsleitung: ein
STAT_OBD_LINK = 1 01 .
STAT_OBD_LINK_TEXT = OBD Link: ein
STAT_HU_AKTIVIERUNGSLEITUNG = 1 01 .
STAT_HU_AKTIVIERUNGSLEITUNG_TEXT = HU Aktivierungsleitung: ein
JOB_STATUS = OKAY
_REQUEST = 3 Bytes
0000 : 22 40 31 "@1
_RESPONSE = 6 Bytes
0000 : 62 40 31 01 01 01 b@1...
---------------------------------------------------------------------------------
RE: NBT Evo bench test can not ping - DEJMIEN - 03-12-2023
I had the same problem ages ago, just add 1 wire ETH_A, from ZGW plug 3B pin 13 to quadlock pin 29.
RE: NBT Evo bench test can not ping - alsamaraee - 03-12-2023
(03-12-2023, 20:46 PM)DEJMIEN Wrote: I had the same problem ages ago, just add 1 wire ETH_A, from ZGW plug 3B pin 13 to quadlock pin 29.
Does not help.
RE: NBT Evo bench test can not ping - walkernight88 - 03-12-2023
(03-12-2023, 20:52 PM)alsamaraee Wrote:(03-12-2023, 20:46 PM)DEJMIEN Wrote: I had the same problem ages ago, just add 1 wire ETH_A, from ZGW plug 3B pin 13 to quadlock pin 29.
Does not help.
and what about STATUS_ETHERNET_REGISTER_LESEN? does the registry show a 100mbps link between HU and ZGW?
RE: NBT Evo bench test can not ping - alsamaraee - 03-12-2023
(03-12-2023, 21:36 PM)walkernight88 Wrote:(03-12-2023, 20:52 PM)alsamaraee Wrote:(03-12-2023, 20:46 PM)DEJMIEN Wrote: I had the same problem ages ago, just add 1 wire ETH_A, from ZGW plug 3B pin 13 to quadlock pin 29.
Does not help.
and what about STATUS_ETHERNET_REGISTER_LESEN? does the registry show a 100mbps link between HU and ZGW?
| zgw enet hu.txt | ||
| File Type: |
|
 |
| Downloaded: | 38 times | |
| Size: | 27.35 KB | |