+- CarTechnoloGY (https://cartechnology.co.uk)
+-- Forum: All About IMMO/ECU , ChiPTuninG , Dashboard , Locksmith , AirbaG , Carradio (https://cartechnology.co.uk/forumdisplay.php?fid=3)
+--- Forum: DASHBOARD (https://cartechnology.co.uk/forumdisplay.php?fid=10)
+--- Thread: VW Sharan - Dash 7M3 920 840 N Pinout (/showthread.php?tid=90016)
VW Sharan - Dash 7M3 920 840 N Pinout - arturjfonseca - 12-03-2024
Hi there.
Does anyone have the pinout for a VDO cluster with the below references:
VW OEM-7M3 920 840 N
FORD OEM - YM21 10849
VDO 110.080/032/013
I've replaced the display, for a Minitools one, and the pinout that they reference doesn't work.
Thanks.
AF
RE: VW Sharan - Dash 7M3 920 840 N Pinout - kastanka - 13-03-2024
32-pin connector T32a, green:
4 -
CAN data bus, screening for input signals
6 -
Washer fluid low
7 -
Brake pad wear
8 -
Infotainment CAN data bus, high input signal
9 -
Infotainment CAN data bus, low input signal
10 -
Radio-controlled clock (earth)
13 -
Handbrake warning lamp
15 -
Infotainment CAN data bus, high input signal
16 -
Infotainment CAN data bus, low input signal
18 -
Oil temperature sender, RPM signal
19 -
CAN data bus, high input signal
20 -
CAN data bus, low input signal
21 -
Bulb failure and failure of headlight range control
22 -
ESI
23 -
MFI call-up button - top
24 -
MFI call-up button - bottom
25 -
MFI save switch - reset
26 -
Ambient temperature sensor input signal
27 -
CAN data bus, high output signal
28 -
CAN data bus, low output signal
30 -
Radio/navigation - clock
31 -
Radio/navigation - data
32 -
Radio/navigation - enable
32-pin connector T32, blue:
1 -
Terminal 15, positive
2 -
Right turn signal warning lamp
3 -
Electronic speedometer output signal
4 -
Trailer turn signal warning lamp
5 -
Fuel gauge
6 -
Electronic throttle
7 -
Terminal 31, sender earth
8 -
Coolant temperature gauge
9 -
Terminal 31, earth
10 -
Oil pressure switch
11 -
Front passenger door contact switch
12 -
Alternator warning lamp, terminal 61
14 -
Rear fog light warning lamp
15 -
Rear left door contact
16 -
Rear lid open warning lamp
17 -
Main beam warning lamp, terminal 56a
18 -
Left turn signal warning lamp
20 -
Dash panel insert illumination, terminal 58b
21 -
Driver door contact switch
22 -
Cooling system low level indicator
23 -
Terminal 30, positive
24 -
Terminal 31, earth
25 -
Self-diagnosis K-wire
26 -
Right parking light
27 -
Left parking light
28 -
Input signal to electronic speedometer
29 -
Brake system warning lamp
30 -
S-contact
31 -
Seat belt warning system (only certain countries)
32 -
Rear right door contact
RE: VW Sharan - Dash 7M3 920 840 N Pinout - ady2006 - 13-03-2024
I don't remember any pinouts on minitool site. If you refer to internal pads from pcd, where lcd is soldered, your request is useless.
The new display fit or not fit to your cluster. If you bought wrong display type, cannot solve the problem.
RE: VW Sharan - Dash 7M3 920 840 N Pinout - arturjfonseca - 13-03-2024
(13-03-2024, 07:30 AM)ady2006 Wrote: I don't remember any pinouts on minitool site. If you refer to internal pads from pcd, where lcd is soldered, your request is useless.
The new display fit or not fit to your cluster. If you bought wrong display type, cannot solve the problem.
Hi.
In the Minitool's instructions for this display , it has the pinout for 12v and ground
[img]
![[Image: Captura-de-ecr-2024-03-13-085630.png]](https://i.postimg.cc/Ff3MxHnf/Captura-de-ecr-2024-03-13-085630.png)
[/img]
RE: VW Sharan - Dash 7M3 920 840 N Pinout - ady2006 - 13-03-2024
I missed it. Normally, it must work with pins 1, 7 and 23.
Add gnd (negative) at pin 9 and pin 24. And eventually +12V at pin 30.