Consult III Plus with Ford VCM II - Printable Version +- CarTechnoloGY (https://cartechnology.co.uk) +-- Forum: Discussions All about Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=310) +--- Forum: Automotive Help & Discussions / Software and Hardware (https://cartechnology.co.uk/forumdisplay.php?fid=40) +---- Forum: Renault - Dacia - Nissan - Infiniti (https://cartechnology.co.uk/forumdisplay.php?fid=57) +---- Thread: Consult III Plus with Ford VCM II (/showthread.php?tid=9446) Pages:
1
2
|
Consult III Plus with Ford VCM II - Joe2 - 14-08-2015 Hi, Could you please share exact manual and, if possible, configuration files for Consult III Plus to run it with Ford VCM II interface. I made some changes in files and registry based on forum manuals but it doesn't see ignition still, interface is recognised in some way. Thanks for any help. RE: Consult III Plus with Ford VCM II - mattydr67 - 14-08-2015 Forget about The Ignision ON its not seen if you use VCM II I use AVDI and Ignision ON it is not seen too I read that no matter what j2534 tool you use the Ignition ON its not seen I understood that only if you use Alliance VI2 Same you cannot see live data parameters. Good luck RE: Consult III Plus with Ford VCM II - Joe2 - 14-08-2015 Thanks, could you please share your configuration files and registry settings for AVDI ? I think that I am doing something worng because it does not connecting to the car. Generally, the error is in interface connection menu. It see interface , name is 12345 and when I push connect button there is an error. RE: Consult III Plus with Ford VCM II - mattydr67 - 15-08-2015 Mate Install the passtrue drivers for AVDI The configuration file is the same and write the name your tool from registry I'm using it as a passthru so you have write there APTxxxxx ( xxxxx- your tool S/N ) Nothing special sir Good luck RE: Consult III Plus with Ford VCM II - Joe2 - 18-08-2015 I know what I was doing wrong. I was trying to connect to interface first. But when I pick-up appropriate car and push button connect it works great ! Of course, I had ingintion error but modules was recoginsed without problem, Hope it will help someone. RE: Consult III Plus with Ford VCM II - flywin - 19-02-2016 men how to connect, VCM II with Nissan Consult +? any advice RE: Consult III Plus with Ford VCM II - someonefromistra - 21-02-2016 (19-02-2016, 09:32 AM)flywin Wrote: men how to connect, VCM II with Nissan Consult +? Found this on another forum. I tested it once with limited succes. For ford VCMII Install the consult 3 plus Change diagnostictool.ini file in Nissan instalation folder Install your VCMII Manager and drivers. In passhru 4.04 in reg edit and rename NISSAN_VI2 To something else change name Bosch Ford-VCM-II to NISSAN_VI2 Reboot computer and test it RE: Consult III Plus with Ford VCM II - Inspector_Gadget - 21-02-2016 (21-02-2016, 12:01 PM)someonefromistra Wrote:(19-02-2016, 09:32 AM)flywin Wrote: men how to connect, VCM II with Nissan Consult +? in diagnostic tools.ini put Ford-VCM-II RE: Consult III Plus with Ford VCM II - meiguang - 11-08-2016 Just wanna sharing, I have tested on nissan xtrail 2015 and 2016, it seems not run properly, just only dtc and ecu part id was detected, even can't see live data, torque via android even seems better...hihi Does anyone could fix this problem, or maybe wrong setting? Thanks in advanced RE: Consult III Plus with Ford VCM II - mattydr67 - 29-11-2016 Only with real Nissan Alliance VI2 you will see the live data in all cars Using a J2534 tool you will see item in some cars but in most of them you will not The Ignision status isn't available for a J2534 tool too Good luck |