Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
F40 icam retrofit on entrynav2
16-03-2024, 10:21 AM,
(This post was last modified: 16-03-2024, 11:13 AM by Bavrian.)
Post: #1
|
|||
|
|||
F40 icam retrofit on entrynav2
I have a f40 2020 with entrynav2 that i want to install reverse camera too
It doesn’t have ethernet switch. Camera is Icam2 it’s g30 model Icam2-R with original g30 Icam wiring With power, earth. Ethernet white & green wires and yellow wake up line pins have been tested and connected to the bdc existing wires on pins 37 & 38 con 9 Tested also on pins 1-2 on con 9 too. which has existing wires also on those slots And wake up yellow line connected to existing wake up line on pin 54 in con 8 Car has been fully coded with 3ag or 5dm but the Icam doesn’t show up in esys at all Does the car need Ethernet switch to make Icam work |
|||
16-03-2024, 11:27 AM,
Post: #2
|
|||
|
|||
RE: F40 icam retrofit on entrynav2
Hello, you code ACSM?
O retrofited same ICAM in f44 and no problem, code 3AG in BDC HU and ACSM. Car dont have ethernet switch. |
|||
16-03-2024, 11:27 AM,
(This post was last modified: 16-03-2024, 11:38 AM by Bavrian.)
Post: #3
|
|||
|
|||
RE: F40 icam retrofit on entrynav2
Ok got it working
so iv connected the pins in 1-2 in con 9 and as a test and removed the existing wires in those slots and the camera shows up under esys and works on idrive sceeen So seems a ethernet switch is needed unless anyone has a work around this The (16-03-2024, 11:27 AM)Pedrom92 Wrote: Hello, you code ACSM?Yes acsm was coded Did your car have MGU or entrynav2 As all ethernet slots on bdc are taken up on pin 1-2 & 37-38 |
|||
16-03-2024, 11:39 AM,
Post: #4
|
|||
|
|||
RE: F40 icam retrofit on entrynav2
(16-03-2024, 11:27 AM)Bavrian Wrote: Ok got it working Have MGU unit. But no switch. |
|||
16-03-2024, 12:32 PM,
(This post was last modified: 16-03-2024, 12:34 PM by Node.)
Post: #5
|
|||
|
|||
RE: F40 icam retrofit on entrynav2
First - there is a service function in ISTA to open connected ethernet ports. You don't tell us if you performed it (or corresponding job with tool32). If port was NOT used before it is CLOSED.
Second - you CAN'T connect multiple ethernet devices to the same port. If ALL ports on BDC are already used, you SHALL need the switch. |
|||
16-03-2024, 12:56 PM,
(This post was last modified: 16-03-2024, 13:01 PM by Bavrian.)
Post: #6
|
|||
|
|||
RE: F40 icam retrofit on entrynav2
Pedrom92 dateline='[url=tel:1710589174' Wrote: 1710589174[/url]'] I have noticed many installs have all been on cars with MGU mainly Similar to g30 they always had free port locations on cars with evo & mgu (16-03-2024, 12:32 PM)Node Wrote: First - there is a service function in ISTA to open connected ethernet ports. You don't tell us if you performed it (or corresponding job with tool32). If port was NOT used before it is CLOSED. The ista job was carried out before trying the above pin change that made it work Yes all ports are occupied Seems the answer is a ethernet switch |
|||
16-03-2024, 13:13 PM,
(This post was last modified: 16-03-2024, 13:20 PM by Lpapp.)
Post: #7
|
|||
|
|||
RE: F40 icam retrofit on entrynav2
(16-03-2024, 12:56 PM)Bavrian Wrote:Pedrom92 dateline='[url=tel:1710589174' Wrote: 1710589174[/url]'] if 1+2 or 19+20 or 37+38 is allready in use, than you have to install ethernet swith and connect kafas with icam to swith. yesterday i have install ICAM with swith in F40. you have to buy 61 35 5A0A438 61 13 9368538 and look for connector in air: A376*1B and 2x A376*2B |
|||
16-03-2024, 14:54 PM,
Post: #8
|
|||
|
|||
RE: F40 icam retrofit on entrynav2
Lpapp dateline='[url=tel:1710594802' Wrote: 1710594802[/url]'] Thanks yes all 3 of these are occupied will look at getting the switch & parts |
|||
17-03-2024, 10:18 AM,
Post: #9
|
|||
|
|||
RE: F40 icam retrofit on entrynav2
(16-03-2024, 14:54 PM)Bavrian Wrote: Thanksyou have to buy 61 35 5A0A438 swith 61 13 9368538 holdingplate for connectors 1x 61 13 9353105 connector 10 pins 2x 61 13 9353106 connector 6 pins if you have crimping pliers for NanoMQS than 61 13 9230107 otherwise 61 13 0056943, 15pcs will be enough. |
|||
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
F20 cruise control retrofit | maninblack | 5 | 128 |
Yesterday, 18:09 PM Last Post: qbek90 |
|
BMW e87 LCI hralights retrofit problem | XeoN | 0 | 22 |
21-05-2024, 21:17 PM Last Post: XeoN |
|
Tool to use to cut leather dashboard for hud retrofit | Fx82 | 3 | 308 |
19-05-2024, 15:29 PM Last Post: Fx82 |
|
F01 LCi Xenon Headlight Retrofit | mcrussell | 0 | 54 |
16-05-2024, 11:57 AM Last Post: mcrussell |
|
retrofit USB BMW E63 | Jalami | 9 | 257 |
15-05-2024, 17:39 PM Last Post: The CaT |
|
Retrofit comfort access BMW f26 | santopalermo | 13 | 420 |
14-05-2024, 12:25 PM Last Post: ruben_17non |
|
Help for front and rear camera with iCam in e9x | ruben_17non | 0 | 73 |
13-05-2024, 13:54 PM Last Post: ruben_17non |
|
F25 cic retrofit | hero3838 | 3 | 111 |
10-05-2024, 15:44 PM Last Post: Siki78 |
|
G21 paddles retrofit | bm92 | 5 | 225 |
09-05-2024, 21:07 PM Last Post: bm92 |
|
Is it possible to retrofit G30 seat to G20? | hitit | 0 | 107 |
08-05-2024, 14:22 PM Last Post: hitit |
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content