Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
DIGIPROG 3 user help thread !
01-07-2015, 03:19 AM,
Post: #151
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
(30-06-2015, 22:32 PM)mrmx Wrote:(30-06-2015, 06:13 AM)Dayo Wrote: Post a pic of the dash mate. Iv done a 64 plate via obd with digi, but it was the last of the old shape. here is some pic's of the digiprog's on screen errors & end result fails on the mk4 2010 ford mondeo tdci diesel (cd345 ba7) still needing help if possible? but if not even another product suggestion that will work for odometer correction on this car? thanks again |
|||
03-07-2015, 09:35 AM,
(This post was last modified: 03-07-2015, 09:36 AM by Dayo.)
Post: #152
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
(01-07-2015, 03:19 AM)mrmx Wrote:a 2010 mondeo should be 24c16 eeprom. if it says chip not found when you clip it, then you need to unsolder it. i dont recommend reading whilst on the board, but yes we all do it for ease.(30-06-2015, 22:32 PM)mrmx Wrote:(30-06-2015, 06:13 AM)Dayo Wrote: Post a pic of the dash mate. Iv done a 64 plate via obd with digi, but it was the last of the old shape. so desolder and clip it in the clip. should be fine then mate. click thanks lexus is220 did as a is200 with 93c56 chip Stop getting worried about what could go wrong, and start getting excited about would could go right!
hmmmmmmm........eeprom!!! Digi v4.94, Xtool, R260, R270, Smok, VagProg DataSmart 3+ Smelecom, Autel Maxisys ms908 |
|||
06-07-2015, 23:27 PM,
Post: #153
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Ok,
i have found a chip that the pomona clip (5250) fits & is directly behind the lcd odo etc display in a cluster of components that are local to the lcd area also (see pic 1). the chip has the numbers 33063v & pgsf on it? however there are two other chips the same that the clip will also fit directly beside each other that are further away from the lcd but have a different number (nxp t ja1040) on them both (see pic 2 end of pen..pic is upside down though). any theories on this? & if i put the digiprog on them while still on the board, will it first tell me that it can either read or not recognize without damage? & also if i turn the clip around the other way & try again? (i notice that the clip has a wee bit of black marker pen on one side, (as in pic 1..maybe negative? but which pin?) the 2nd last pic is a close up of the last pic. ive only ever had to use the obd port on cars to sort issues hence i am a bit unclear on this side of things & dont want to damage components etc, so any help to resolve this odo correction would be very much appreciated! thanks all |
|||
07-07-2015, 00:49 AM,
Post: #154
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
This is dash with 9s12 micro no eeprom on this
|
|||
07-07-2015, 01:08 AM,
Post: #155
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Ok thanks,
so what can be done to do odo change for a new motor? is there another product that can? or upgrades for the digiprog? or any suggestions? thanks again |
|||
07-07-2015, 06:30 AM,
Post: #156
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
(07-07-2015, 01:08 AM)mrmx Wrote: Ok thanks, Hello mate. I've never not known digi not to do this speedo via obd. I have done lots of them via obd using v4.88. Does it light up orange/red when in car? Smok ford will be your next option here I would have thought |
|||
07-07-2015, 07:13 AM,
Post: #157
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Hi thanks for your input.
does what light up orange/red? do you mean the lcd display( just to be clear?) & where can i get smok ford download from? thanks again |
|||
07-07-2015, 14:19 PM,
Post: #158
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
Yes the dash light up display ect. Smok is a company smok.pl
|
|||
08-07-2015, 20:27 PM,
Post: #159
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
|
|||
09-07-2015, 20:53 PM,
Post: #160
|
|||
|
|||
RE: DIGIPROG 3 user help thread !
(07-07-2015, 06:30 AM)scully Wrote:(07-07-2015, 01:08 AM)mrmx Wrote: Ok thanks, ok so i tried again, & the same thing "unknown version". the dash, hazard lights & chime sounds all went off then all lite up in red/orange color as per norm for the lcd, & dash sounded again also. didgiprog seems to run through a scan that takes a few second but it comes up "unknown version" thanks again. tried to upload a video but didnt work by the looks of things |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
3 Guest(s)
3 Guest(s)
Return to TopReturn to Content