[delic]

KTM Bench 1.20

Module 71

EDC17C64 - Read/Write - OK
VW Golf VII 2014 1.6 TDI 77kw

Bosch SW.: 0 281 018 510
Part Nr.: 04L 907 309 B

[Carremapper]

I have use ori Scanmatic 2 Pro
Modules: 50, 65, 71, 77, 84, 87, 92 All ok
EDC17xxx, MED9.1, EDC16xx, DCM6.2A, DCM6.2V, Ford EECV with Ori all okay excellent!

Are you using the china clone 1.20/1.21 and ori PCM Flash in one windows or with other computer?
Thx

[ipmk7]

i have tactrix ori and clone one
mongoose-plus Vw audi
pcm powerbox (use it for tcu)

software i use original one
ktm 1.29 (tcu)
pcm tuner dongle 1.2.7

for R W TCU the ktm or the original or the pcm tuner work great
for the cable the 3 work great to no problem with the clone one (with pcm box)

for the module 82 i was not able to make it work with the tactrix (ori or clone one) work with the mongoose-plus (with pcm box)

module 57 with ori software and pcm tuner all work perfect, samething for the 3 cable


the only problem with the clone cable tactrix is some time the cable die

[Inovator]

Anyone used module 91 for CRD3Plus on bench via scanmatik? I got failure after ignition on prompt.

[Carremapper]

Anyone used module 91 for CRD3Plus on bench via scanmatik? I got failure after ignition on prompt.

Check scanmatic drivers if not the latest download and install it.
I had few weeks ago similar trouble with module 92 MG/MD1 bootloader protokoll (Original SM2PRO and Ori PCMFlash)

[jim jones]

I have an original  PCMFLASH version 1.34. I know that past 1.20 you can't use this over the internet. I have tried to revert to 1.20 without success with all types of USB redirects.
Does anyone have a working solution to this issue. Willing to pay. I need to use this over the internet.
Thanks

[hachimuto]

Sometimes it stops uploading file to the ECU and it remains stuck in boot mode. To overcome this problem, you must have downloaded the password file from your ECU and use an nochksum file in tricore section.
if you don't have downloaded the password use mpps to download the password and try to exit the ECU from boot mode.

[delic]

KTM Bench 1.20

Module 71

EDC17CP14 - Read/Write - OK
VW Golf VI 2009 2.0 TDI 81kw

[delic]

KTM Bench 1.20

Module 54

DCM3.7 - Read/Write OBD - OK
Seat Ibiza 1.2 TDI 55KW 2011

[kwork]

Solved!

I tried to write BIN again.
same as EEProm and Flash was a little different. but because skip one address.
almost as same Flash.

Then The car was started and runs good no issue.

just read and write for PCMFlash and SM2Pro.

Thank you.


Hello,

Please give me an advice ECU professionals.

I want to make clone ECU for PSA Bosch MED17.4.2.

I have Scanmatik2Pro and PCMFlash module 71.

I tried to read EEProm and Flash BIN from Original ECU and Donor ECU.
and wrote original ECU BIN files to Donor ECU.
then I read donor ECU both BIN files but different data from original data.

Can I make clone for MED17.4.2 MEDC17 TC1767?
Do I have to open ECU box?
Please tell me a correct method.

Can anyone help me?