Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Flashing NBT Evo on Bench
24-04-2022, 09:38 AM,
Post: #7
|
|||
|
|||
RE: Flashing NBT Evo on Bench
I have the hu-evo2 connected to ZGW2-4sk via can-bus. I made even ethernet cable to OARB connector but not wired to ZGW.
Tried to flash but get error C207. What FA and I-steps should I use are they from the G-series that the HU come from or the one from my car F11(jan-2012)? Should I connect as G/F? < TAL execution started. ExecutionID=2022/04/24-11:03:31.152 [] prepareTALExecution started [PROGRESS] [] prepareTALExecution finished [PROGRESS] [] prepareVehicleForFlash started [PROGRESS] [] prepareVehicleForFlash finished [PROGRESS] MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE] MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE] MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE] MCDDiagService<id=242900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_SDB - RoutineControl SetDefaultBus, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE] [] Activate programming mode was not successful for: ECUId:HU_NBT2_0x63 [WARN] [] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [WARN] [HU_NBT2 - 63] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [THROWABLE] [] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [WARN] [] finalizeVehicleFlash started [PROGRESS] [] finalizeVehicleFlash finished [PROGRESS] [] prepareVehicleForCoding started [PROGRESS] [] prepareVehicleForCoding finished [PROGRESS] [] finalizeVehicleCoding started [PROGRESS] [] finalizeVehicleCoding finished [PROGRESS] [] finalizeTALExecution started [PROGRESS] [] finalizeTALExecution finished [PROGRESS] TAL execution finished [TAL_EXECUTION_FINISHED] TAL-Execution finished with status: "FinishedWithError". [C207] TAL execution finished. Duration: "2min 13s". [C206] Read SVT after TAL execution started. Read SVT after TAL execution finished. > This is the log when I flshing via zgw. Get the blue screen on the HU and then reboot. |
|||
« Next Oldest | Next Newest »
|
Messages In This Thread |
Flashing NBT Evo on Bench - by ady_e_n - 26-07-2019, 20:18 PM
RE: Flashing NBT Evo on Bench - by sameur10 - 27-07-2019, 08:51 AM
RE: Flashing NBT Evo on Bench - by ady_e_n - 29-07-2019, 16:52 PM
RE: Flashing NBT Evo on Bench - by alsamaraee - 17-04-2022, 12:40 PM
RE: Flashing NBT Evo on Bench - by ady_e_n - 17-04-2022, 12:43 PM
RE: Flashing NBT Evo on Bench - by alsamaraee - 17-04-2022, 12:46 PM
RE: Flashing NBT Evo on Bench - by alsamaraee - 24-04-2022, 09:38 AM
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content