Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
ISTA-D 3.56.14.16733 Standalone V2
|
01-07-2016, 09:13 AM,
Post: #51
|
|||
|
|||
|
RE: ISTA-D 3.56.14.16733 Standalone V2
No. the system tray works without any problems. i chose a different driver and now it works.
but ista was the only problem. everything else printed fine. ISTA 4.46.14, ISTA 4.46.11 SDP, ISTA-P 72.0, ISTA Launcher 1.46
E-Sys Launcher Pro 5.2.4 with E-Sys 22.10 Lenovo P14s |
|||
|
![[+]](https://cartechnology.co.uk/images/CarTechnologyTheCure/collapse_collapsed.png)
|
01-07-2016, 17:04 PM,
Post: #52
|
|||
|
|||
|
RE: ISTA-D 3.56.14.16733 Standalone V2
Can anyone confirm if the programming function on ISTA+ only works with ICOM, but not ENET?
I used a ENET and tried to calculate the test plan, but failed. Here is the log message: 2016-06-30 21:26:40 INFO [T] ISTA: [25] ConnectToBn2020VehicleState.Handle() - Connecting to vehicle... 2016-06-30 21:26:40 INFO [T] ISTA: [25] ConnectToBn2020VehicleState.Handle() - Try to find newest target selector by main series 'F020'... 2016-06-30 21:26:40 INFO [T] ISTA: [25] ConnectToBn2020VehicleState.Handle() - Target selector found: TargetSelector: Project=F020_16_03_504, VehicleInfo=F020 2016-06-30 21:26:55 WARNING [T] ISTA: [25] ConnectToBn2020VehicleState.ConnectToProject() - Connection (ProjectName: 'F020_16_03_504', VehicleInfo: 'F020') failed! (connection.Check(): false) 2016-06-30 21:26:56 ERROR [T] ISTA: [25] ConnectToBn2020VehicleState.Handle() - Failed! 2016-06-30 21:26:56 INFO [T] ISTA: [25] ConnectToBn2020VehicleState.Run() - ...finished with: DefaultStateResult.Error - "" |
|||
|
|
|
01-07-2016, 17:21 PM,
Post: #53
|
|||
|
|||
|
RE: ISTA-D 3.56.14.16733 Standalone V2
|
|||
|
|
|
01-07-2016, 17:39 PM,
Post: #54
|
|||
|
|||
RE: ISTA-D 3.56.14.16733 Standalone V2
(01-07-2016, 17:21 PM)aboulfad Wrote:(01-07-2016, 17:04 PM)bmwdd Wrote: Can anyone confirm if the programming function on ISTA+ only works with ICOM, but not ENET?Like most of us too got an error, it only works with ICOM. It does look strange to me because the error occurs right at the beginning, when ISTA+ tries to connect the car using VechileInfo=F020 and then suddenly it throws error. But ENET cable should have no trouble to connect to the car in both esys and ISTA+ I'm thinking if we're missing something very basic or trivial.... |
|||
|
|
|
01-07-2016, 17:49 PM,
Post: #55
|
|||
|
|||
|
RE: ISTA-D 3.56.14.16733 Standalone V2
ISTA+ and Programming works only with ICOM. Error is also because of the reason that the ENET interface will not show KL15 and 30.
|
|||
|
|
|
01-07-2016, 18:22 PM,
Post: #56
|
|||
|
|||
RE: ISTA-D 3.56.14.16733 Standalone V2
(01-07-2016, 17:39 PM)bmwdd Wrote: ...I have heard rumours that it may work with many changes to networking Config and using ICOM emulator but details are sketchy and apparently it will be very slow. I use Esys when I need to flash and call it a day as I don't want to invest in an ICOM I/F as Esys does everything and more (you can flash individual ECUs, code, ...) |
|||
|
|
|
02-07-2016, 12:00 PM,
Post: #57
|
|||
|
|||
|
RE: ISTA-D 3.56.14.16733 Standalone V2
Hi, can someone tell me how many GB has to be the drive to install ista-d and ista-p
regards |
|||
|
|
|
02-07-2016, 15:19 PM,
Post: #58
|
|||
|
|||
RE: ISTA-D 3.56.14.16733 Standalone V2
|
|||
|
|
|
02-07-2016, 18:20 PM,
Post: #59
|
|||
|
|||
RE: ISTA-D 3.56.14.16733 Standalone V2
(02-07-2016, 12:00 PM)tecnijl Wrote: Hi, can someone tell me how many GB has to be the drive to install ista-d and ista-p Standalone: 122 GB (ISTA-D 19.9 GB, ISTA-P 102 GB) |
|||
|
|
|
02-07-2016, 21:10 PM,
Post: #60
|
|||
|
|||
|
RE: ISTA-D 3.56.14.16733 Standalone V2
I have question about rheingold configuration with enet cable. Where should I write 169.254.1.1 ip address, in wifi's protocol 4?
|
|||
|
|
|
« Next Oldest | Next Newest »
|
Users browsing this thread:
3 Guest(s)
3 Guest(s)
Return to TopReturn to Content
