[beemerboy88]

The main psdzdata folder extracted from BMW_ISPI_ISTA-SDP_FULL_4.01.15 is to small with 37.8gb
Full one from ista p psdzdata 59.4 has 60GB.

Not sure about this, but ISTA-P is also for E Series. ISTA 4 is only for F, G and I Series. Maybe that's the reason the new psdzdata folder is smaller now...

It needs to be installed using the launcher. Should be 62GB.

[Orphee]

The main psdzdata folder extracted from BMW_ISPI_ISTA-SDP_FULL_4.01.15 is to small with 37.8gb
Full one from ista p psdzdata 59.4 has 60GB.

Not sure about this, but ISTA-P is also for E Series. ISTA 4 is only for F, G and I Series. Maybe that's the reason the new psdzdata folder is smaller now...

It needs to be installed using the launcher. Should be 62GB.

May I ask you to explain how the launcher works in case we have a valid license ?
Just need to put all files in sharedfolder and start launcher ? what are the prerequisite ?
Thank you

[qwe1211208256]

Hi Thanks, But your link doesnt work

[hulahans]

Standalone diagnosis works quite good, but i can not make measurement Plan.

Everytime Ista says i have to test the car first, and i have done that several times.
Before i copied complete psdzdata folder from ista p 59.4 to C:\Rheingold\PSdZ\data

Dont know whats wrong, but i only tested with ETH (ignition voltage was not shown ) not with my icom next.
Any ideas?

I'm not sure but in the last versions I had the same Problem with ETH cable. Everything works when I use an ICOM. Try it with your ICOM Next.

I have tested now again with icom next, diagnosis works but programming same result as with eth. I have to test the car first, although i did that several times.
Someone have another idea?

[aboulfad]

I have tested now again with icom next, diagnosis works but programming same result as with eth. I have to test the car first, although i did that several times.
Someone have another idea?

Sorry this won't help, but I recall you, I and others had this same issue back in Jan/Feb this year using 3.54 ... I gave up on programming using ISTA/D and exclusively use Esys. http://cartechnology.co.uk/showthread.ph...734&page=5

One conclusion is that a physical ICOM is needed, not emulator and doesn't work with ENET but you seem to be back to square 0 even with ICOM!

[beemerboy88]

Standalone diagnosis works quite good, but i can not make measurement Plan.

Everytime Ista says i have to test the car first, and i have done that several times.
Before i copied complete psdzdata folder from ista p 59.4 to C:\Rheingold\PSdZ\data

Dont know whats wrong, but i only tested with ETH (ignition voltage was not shown ) not with my icom next.
Any ideas?

I'm not sure but in the last versions I had the same Problem with ETH cable. Everything works when I use an ICOM. Try it with your ICOM Next.

I have tested now again with icom next, diagnosis works but programming same result as with eth. I have to test the car first, although i did that several times.
Someone have another idea?

psdzdata in ista 4.01.21 is 62GB vs 60GB for ISTA/P. But probably not the cause of the problems you are having.

[Bimmer540]

Standalone diagnosis works quite good, but i can not make measurement Plan.

Everytime Ista says i have to test the car first, and i have done that several times.
Before i copied complete psdzdata folder from ista p 59.4 to C:\Rheingold\PSdZ\data

Dont know whats wrong, but i only tested with ETH (ignition voltage was not shown ) not with my icom next.
Any ideas?

And what is the value in istagui exe config
Path in istagui exe config was wrong
<!-- Enable Programming -->
<add key="BMW.Rheingold.Programming.PsdzDataPath" value="c

I'm not sure but in the last versions I had the same Problem with ETH cable. Everything works when I use an ICOM. Try it with your ICOM Next.

I have tested now again with icom next, diagnosis works but programming same result as with eth. I have to test the car first, although i did that several times.
Someone have another idea?

psdzdata in ista 4.01.21 is 62GB vs 60GB for ISTA/P. But probably not the cause of the problems you are having.

What files do I need and what location must I place that files for programming with Ista 4.

[hulahans]

Path in istagui exe config was wrong
<!-- Enable Programming -->
<add key="BMW.Rheingold.Programming.Enabled" value="true" />
<add key="BMW.Rheingold.Programming.ExpertMode" value="true" />
<add key="BMW.Rheingold.Programming.PsdzDataPath" value="c:\esysdata\psdzdata"/>

But don t think that it will solve my problem

---

So, i got it, changed the path with different settings and now programming /measurement plan works

---

My psdzdata 59.4 folder i copied to C:\Rheingold\PSdZ\data



and i changed istagui path to this
<!-- Enable Programming -->
<add key="BMW.Rheingold.Programming.Enabled" value="true" />
<add key="BMW.Rheingold.Programming.ExpertMode" value="true" />
<add key="BMW.Rheingold.Programming.PsdzDataPath" value="c:\Rheingold\PSdZ\data"/>

[dracon]

The main psdzdata folder extracted from BMW_ISPI_ISTA-SDP_FULL_4.01.15 is to small with 37.8gb
Full one from ista p psdzdata 59.4 has 60GB.

Not sure about this, but ISTA-P is also for E Series. ISTA 4 is only for F, G and I Series. Maybe that's the reason the new psdzdata folder is smaller now...

Yes, the ISTA-D data only contains BN2020 vehicle data (F, G, I, newer RR) which is why it's smaller. It doesn't contain any E series data.

ISTA-P will contain all chassis data until around August 2017, then BMW plans to phase out all BN2020 vehicle data in ISTA-P. So ISTA-P will be E-series only and ISTA 4 will be everything else.

[fxx1314]

How to use this program