Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Xentry OpenShell PassThru 09-10-11.2016
15-11-2017, 00:24 AM, (This post was last modified: 18-11-2017, 12:23 PM by HERVE06300.)
Post: #71
RE: Xentry OpenShell PassThru 09-10-11.2016
HELLO
Windows 10 native intaled 3 days ago
I have VAS 5054A with serial #083600808
When I try to install drivers windows says "not found drivers"
any idea/solution ?

here pics of my vas5054a PCB

[Image: img_2010.jpg]

[Image: img_2011.jpg]

the good think is that you don't need to unsoldering ram memories smile
Quote this message in a reply
16-11-2017, 15:15 PM,
Post: #72
RE: Xentry OpenShell PassThru 09-10-11.2016
1. That is by far the worst VAS5054a clone I have seen.

2. You need to be on Win 7-10 32-bit and install the drivers correctly. See the instructions, they were very well written.
Quote this message in a reply
16-11-2017, 16:44 PM, (This post was last modified: 16-11-2017, 17:02 PM by Clusters.)
Post: #73
RE: Xentry OpenShell PassThru 09-10-11.2016
1. That is by far the worst VAS5054a clone I have seen.

That's I supposed

2. You need to be on Win 7-10 32-bit and install the drivers correctly. See the instructions, they were very well written.


I do all but I plug vas5054a (I block W10 to install automatically drivers) I see Vas5054 i make "driver update" and i chose good place But I Have "no driver found"

I suppose my vas5054 is very bad
But work to read audi s4 b8 (usb mode only)
Quote this message in a reply
17-11-2017, 00:57 AM,
Post: #74
RE: Xentry OpenShell PassThru 09-10-11.2016
Another question

Tomorrow I can use original KTS of a friend

How I can change vas5054a passthru to kts pasthru in xentry ?
Quote this message in a reply
02-12-2017, 16:18 PM,
Post: #75
RE: Xentry OpenShell PassThru 09-10-11.2016
With a new vas5054a vci works fine with

smart 450 (kiss point of clutch)
smart 451 (kiss point of clutch)

The only think is when ignition on/off :

FIRST TIME USE THE KEY after change the file

But don't work with w208.444 2002 normal or not ?
Quote this message in a reply
03-12-2017, 23:19 PM, (This post was last modified: 03-12-2017, 23:21 PM by konstantin82.)
Post: #76
RE: Xentry OpenShell PassThru 09-10-11.2016
No pass in DAS special function. Copy that file in folder where DAS instaled.
I recomend not fully replace the old one. Just rename it. Then paste that file.


Attached Files
AppFolder-DAS.zip
File Type: .zip
Downloaded: 64 times
Size: 1.43 KB

Quote this message in a reply
[+] 7 users say Thank You to konstantin82 for this post
07-12-2017, 13:42 PM,
Post: #77
RE: Xentry OpenShell PassThru 09-10-11.2016
(02-12-2017, 16:18 PM)HERVE06300 Wrote:  With a new vas5054a vci works fine with

smart 450 (kiss point of clutch)
smart 451 (kiss point of clutch)

The only think is when ignition on/off :

FIRST TIME USE THE KEY after change the file

But don't work with w208.444 2002 normal or not ?

I just create a 2 .bat files which replace the global.sim in DAS folder. And create shortcuts for them on a tasck panel.
Quote this message in a reply
[+] 2 users say Thank You to konstantin82 for this post
12-12-2017, 19:03 PM,
Post: #78
RE: Xentry OpenShell PassThru 09-10-11.2016
I try to change the file but not work

When I start short test I have this :

[Image: img_2015.jpg]

Ans when I try to open calculator I have :

[Image: img_2014.jpg]

Start multiplexer fail
Possible cause : the diagnostic system data sectors are not complete or defective
contact help line
Quote this message in a reply
14-12-2017, 20:53 PM, (This post was last modified: 14-12-2017, 20:56 PM by konstantin82.)
Post: #79
RE: Xentry OpenShell PassThru 09-10-11.2016
(12-12-2017, 19:03 PM)HERVE06300 Wrote:  I try to change the file but not work

When I start short test I have this :

[Image: img_2015.jpg]

Ans when I try to open calculator I have :

[Image: img_2014.jpg]

Start multiplexer fail
Possible cause : the diagnostic system data sectors are not complete or defective
contact help line

It's happens when you try to diagnose non CAN system. And system on K-Line which using not 7pin of obd2.
In cars from 2005 Xentry Passthru, almost, works fine, except X463 (for mine expirience). On older cars different ecus using different pins in obd plug. To diagnose them you need a multiplexer.
Quote this message in a reply
[+] 2 users say Thank You to konstantin82 for this post
15-12-2017, 10:42 AM,
Post: #80
RE: Xentry OpenShell PassThru 09-10-11.2016
Ok thanks a lot

I will try to find multiplexer smile
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
YTMercedes New 2024 xentry KG? Rik 9 1,321 11 hours ago
Last Post: djtosko
YTMercedes Xentry New Long Key (original key) 1st web free service pesona 1,584 148,028 26-03-2024, 20:25 PM
Last Post: Delphi2002
YTMercedes HHT-Win 64bit With Xentry XDOS 2023.03 One Click JackyTran 6 1,565 26-03-2024, 16:21 PM
Last Post: Djkalash
YTMercedes How to Install Xentry PassThru 03.2022 Flawlessly margut 1 1,629 23-03-2024, 15:29 PM
Last Post: head
YTMercedes Xentry Passthru 06.2023 J2534 Openport VCX + Keygen pitercie 2 468 23-03-2024, 15:29 PM
Last Post: head
  Xentry 2024.03 - PT & XDOS renia1983 19 2,101 17-03-2024, 19:35 PM
Last Post: gcs190
YTMercedes XENTRY DAS Activation Here takis 2,422 618,095 15-03-2024, 10:24 AM
Last Post: Mario68
  03 2024 Xentry Final version ross2018 9 903 14-03-2024, 23:37 PM
Last Post: connector
YTMercedes XENTRY AIO FULL FIX [2023.09-R2 & 2023.12-R2] [UPDATED 21/12/2023] crypt0ninja 153 30,424 06-03-2024, 17:32 PM
Last Post: db8000
  Xentry 09/12.2021 WIFI Solution gcs190 11 4,814 29-02-2024, 13:33 PM
Last Post: gcs190

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content