Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

cas / cluster bench setup
13-10-2018, 03:08 AM, (This post was last modified: 28-11-2018, 16:14 PM by Cniksor.)
Post: #1
XZBMW  cas / cluster bench setup
11/27 UPDATE: SEE PAGE 5 , POST#41 FOR WORKING DIAGRAM.


hello everyone. im trying to build a bench setup so that i can test cas keys/cluster on bench. i got the following parts from a junked vehicle to start with:
obd2 port
cas3
cluster
key holder
start button.

now, from looking online i gathered this is the pinout for connections for each module. now i know this might not be right, im sure their is something im missing that will make this all work together. if anyone can guide me or help me i would highly appreciate it. thank you.

i made this quick drawing on how i think it should be connected or at least give me an idea on connections.
Quote this message in a reply
13-10-2018, 05:14 AM,
Post: #2
RE: cas / cluster bench setup
Mate you need Gateway

BR Eddy
Quote this message in a reply
[+] 1 user says Thank You to 16eddi67 for this post
13-10-2018, 05:47 AM,
Post: #3
RE: cas / cluster bench setup
Your bench can speed is 100 kb/s, but d-can is 500. If your dcan adapter not switchable, you must use gateway. I do it with e70 jbe.
Quote this message in a reply
[+] 1 user says Thank You to rus-bmw for this post
14-10-2018, 06:00 AM,
Post: #4
RE: cas / cluster bench setup
thank you, i knew it wasnt going to be that simple.

so ill need something like image below. any emulator out there i can use instead of this? hopefully i can locate one at the junker.

[Image: s-l1600.jpg]
Quote this message in a reply
14-10-2018, 10:08 AM,
Post: #5
RE: cas / cluster bench setup
You need minimum:
CAS + key socket + button
JBBE (in jbbe there are 3 CAN buses, one for obd2, the other for DDE, DSC, EPS, EKP. Third to CAS, KOMBI, CID, ZBE, KLIMA, MRS, FRM, PDC, FZD ...)
If CAS from Europe is still ELV
I also did something trash in a more extended version:
https://www.youtube.com/watch?v=LnVHZ0ImeZA
Reputation: +1 - ruben_17non [+1]
Quote this message in a reply
[+] 3 users say Thank You to wxwwxw for this post
14-10-2018, 18:40 PM, (This post was last modified: 14-10-2018, 19:02 PM by Cniksor.)
Post: #6
RE: cas / cluster bench setup
(14-10-2018, 10:08 AM)wxwwxw Wrote:  You need minimum:
CAS + key socket + button
JBBE (in jbbe there are 3 CAN buses, one for obd2, the other for DDE, DSC, EPS, EKP. Third to CAS, KOMBI, CID, ZBE, KLIMA, MRS, FRM, PDC, FZD ...)
If CAS from Europe is still ELV
I also did something trash in a more extended version:
https://www.youtube.com/watch?v=LnVHZ0ImeZA

i was able to find a jbe from 3 series at the junkyard today, from matching car i got all the other parts from, exactly like photo i posted.
i found this pinout on this forums but i think it isnt for jbe but JBR, do you happen to know how to connect the wiring?

so i have:
cas
kombi
key holder / start button
jbe
obd2 port


OBD II
1: Ignition Connector Block (wakeup)
2: not connected
3: Ethernet connection to cic quadlock pin 37 (black plug)
4: Gnd Connector Block
5: Gnd Connector Block
6: K-bus high (pin 17 on blue 54 pin jbr plug, x14271)
7: I have this connected to pin 30 (PA-BUS) of the CAS (not sure if this is correct???
8: Ethernet connection to cic quadlock pin 29 (black plug)
9: F_TD this goes to the DME)
10: not connected
11: Ethernet connection to cic quadlock pin 38 (black plug)
12: Ethernet connection to cic quadlock pin 31 (black plug)
13: Ethernet connection to cic quadlock pin 32 (black plug)
14: K-bus low (pin 33 on blue 54 pin jbr plug, x14271)
15: not connected
16: +12v Batt Connector Block

JBR x14270 ( the long black plug)
Pin 23 <----- GND Connector Block

JBR x14271 (the 54pin blue plug)
JBR x14271 Pin 10 = K-bus low <----> CAS X13376 pin 26 = K-bus low
JBR x14271 Pin 46 = K-bus high <----> CAS X13376 pin 35 = K-bus high

Pin 17 K-bus high <----> OBD Pin 6
Pin 33 K-bus low <----> OBD Pin 14

Pin 45 wakeup <----> (ignition) also connected to Pin 1 OBD

JBR x14272 (the 54pin black plug) to 8 pin CID (black cic display plug)
+12v -----> Power to Controller Pin 1
GND -----> GND to Controller Pin 2
Pin 11 <----> K-bus high CID Pin 3
Pin 30 <----> K-bus low CID Pin 4

Pin 1 -----> Power to CID Pin 1
Pin 27 -----> GND to CID Pin 3
Pin 29 <----> K-bus high CID Pin 5
Pin 31 <----> K-bus low CID Pin 6

JBR x4010 23pin plug (that connected to the fusebox base)
Pin 3 <----- +12v Batt (source) Connector Block
Pin 22 <----- +12v Batt (source) Connector Block

CAS X13376 black 41pin plug
Pin 21 <----- +12v Batt Connector Block
Pin 34 <----- +12v Batt Connector Block

Pin 12 <----> GND Connector Block
Pin 25 <----> GND Connector Block

Pin 8 <----> wakeup (ignition)
Pin 26 <----> K-bus low
Pin 35 <----> K-bus high

ELV
Pin 1 <----> GND Connector Block
Pin 2 <----> CAS EL + pin 23 CAS
Pin 3 <----> CAS EL - pin 24 CAS
Pin 4 <----> CAS PA-bus pin 30 CAS

Kombi
Pin 18 <----- GND Connector Block
Pin 9 <----- Power Connector Block
Pin 7 <----> K-bus low Connector Block
Pin 6 <----> K-bus high Connector Bloc
Reputation: +2 - bara001 [+1] , Mwahab [+1]
Quote this message in a reply
[+] 6 users say Thank You to Cniksor for this post
14-10-2018, 19:07 PM,
Post: #7
RE: cas / cluster bench setup
diagrams         nod


Attached Files
1.docx
File Type: .docx
Downloaded: 537 times
Size: 336.45 KB

Reputation: +1 - Tech206 [+1]
Quote this message in a reply
[+] 11 users say Thank You to wxwwxw for this post
15-10-2018, 02:46 AM,
Post: #8
RE: cas / cluster bench setup
thank you for the help. i looked at diagram and think i got it all connected correctly, but when i connect my power source that i have set at 12v, when i power on it drops down to 6v and nothing happens.
Quote this message in a reply
15-10-2018, 12:21 PM,
Post: #9
RE: cas / cluster bench setup
How many Amperes your power supply is capable of?

If my post helps you, please click on Thanks and/or Reputation button.
Quote this message in a reply
[+] 1 user says Thank You to Rawediag for this post
15-10-2018, 12:21 PM,
Post: #10
RE: cas / cluster bench setup
do you have big enugh Power suply ?
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
XZBMW Tool for bench read 8hp Garryq 9 1,557 26-03-2024, 09:32 AM
Last Post: skywoker
XZBMW F80 Cluster - setup iskullbox 2 264 25-03-2024, 14:38 PM
Last Post: Unspec
  Bosch MEVD172H bench backup mrproper 1 248 23-03-2024, 18:43 PM
Last Post: Ratnik1990
  BMW E87 swap M5 V10 coding cluster Pedrom92 0 97 20-03-2024, 22:50 PM
Last Post: Pedrom92
  BMW G02 NBT need FSC instrument cluster swap Mr.Tester 1 125 07-03-2024, 21:10 PM
Last Post: painsage
  BMW g30 MID cluster in g20 help Pedrom92 1 144 07-03-2024, 00:08 AM
Last Post: Pedrom92
XZBMW ESys Launcher PRO Setup 2.8.1 fengyonghua21 400 47,065 28-02-2024, 09:39 AM
Last Post: Pommie
XZBMW ENAV2 bench activation Airbus 10 793 25-02-2024, 08:17 AM
Last Post: jb2005
XZBMW ISTA...setup macchief 17 1,168 17-02-2024, 20:33 PM
Last Post: macchief
  Motronic 3.3.1 bench jaramillo 3 172 13-02-2024, 05:12 AM
Last Post: 2013m5

Forum Jump:


Users browsing this thread:
3 Guest(s)

Return to TopReturn to Content