Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Solved ✔ NBT EVO HW4.1 on the bench
10-12-2018, 10:38 AM, (This post was last modified: 12-01-2019, 16:38 PM by Clusters.)
Post: #1
NBT EVO HW4.1 on the bench
Hi,

I have a NBT EVO HW4.1 and i try to flash it on the bench.

For that i have made my own cables for the quadlock (including ETH_A with 1kOHM to 12v) and the OABR cable, and bought a USB to CAN.

When i send the wake-up message 0x12F 37 7C 8A DD D4 05 33 06 and/or 0x130 45 40 22 8F FE the unit wake-up. But i can ping it (169.254.199.99) for 40s only then the unit goes into sleep mode few seconds, then wake-up 40s, then sleep, and again and again. The screen (8.8" Touch screen) remains black and the fan does not start.

So it seems like there is a need for another message to maintain the unit awake.

Has anyone ever had this case and solved it?

Thank you.
11-12-2018, 00:04 AM,
Post: #2
RE: NBT EVO HW4.1 on the bench
For EVO use iDrive controller or send this ID 563 00 00 00 00 FF FF 00 63
Good luck!
[+] 1 user says Thank You to Vias for this post
13-12-2018, 17:24 PM,
Post: #3
RE: NBT EVO HW4.1 on the bench
I have made some tests and nothing change with the message ID 0x563.
The iDrive contoller is always connected, with or without, nothing change

At the end, i tested with random message and the result is always the same: wake-up 40s, then sleep, wake-up 40s, then sleep, and again and again

What's happen ?
13-12-2018, 20:28 PM,
Post: #4
RE: NBT EVO HW4.1 on the bench
maybe better get a cas + zgw or fem?

FSCMap -> FemtoEVO
portal.femtoevo.com online geration VO/FA by VIN, FSC sets, MGU ViM , FSC for Map Updates ROUTE / EVO / CIC / CHAMP / NBT
MD1/MG1 06.2020+ DME unlocking services.
1CR Enable for 06.2020+ EU cars (G series, petrol/DIESEL - RU only).
NCD sign for coding 2.0 for selected portal users. kiss
instagram: @femtoevo
13-12-2018, 20:58 PM, (This post was last modified: 13-12-2018, 21:01 PM by BugFix.)
Post: #5
RE: NBT EVO HW4.1 on the bench
just ZGW + 0x130 + 0x12F + 0x2F4 + 0x2F7 will be good for F series coded EVO
for G series a few to add

NBTEVO, ENAV2, MGU  - CP OFF, Navi , APPS , Carplay, AA
MGU ID-8-9-10 Cars - Full Region change

NCD Secure Coding 2.0




13-12-2018, 22:07 PM, (This post was last modified: 13-12-2018, 22:14 PM by Vias.)
Post: #6
RE: NBT EVO HW4.1 on the bench
Well guys, I send only this two massage:
12F 37 7C 8A DD D4 05 33 06
563 00 00 00 00 FF FF 00 63
Only EVO+Laptop+Ethernet Cable+CanSender+Supply Power 12v and it work good for Flash, Code and play with it!
I don't use ID 130 and ID 267 or any other.

What is interval you use, more 100 ms? Are you have resistor 120 om in your CAN sender?
13-12-2018, 22:31 PM,
Post: #7
RE: NBT EVO HW4.1 on the bench
NM2_BODY_CAN
1379 (563h) - NBTevo_Rueko [21] {aktiv bei: KL_30B}

Zykluszeit: ttyp = 640.0 ms (tmin = 608.0 ms, tmax = 672.0 ms)
Aktivbedingung = KL_30
Startbedingung = KL_30_ON; Stopbedingung = KL_30_OFF

NBTEVO, ENAV2, MGU  - CP OFF, Navi , APPS , Carplay, AA
MGU ID-8-9-10 Cars - Full Region change

NCD Secure Coding 2.0




14-12-2018, 21:04 PM, (This post was last modified: 14-12-2018, 21:15 PM by BugFix.)
Post: #8
RE: NBT EVO HW4.1 on the bench
(13-12-2018, 22:07 PM)Vias Wrote:  Well guys, I send only this two massage:
12F 37 7C 8A DD D4 05 33 06
563 00 00 00 00 FF FF 00 63
Only EVO+Laptop+Ethernet Cable+CanSender+Supply Power 12v and it work good for Flash, Code and play with it!
I don't use ID 130 and ID 267 or any other.

What is interval you use, more 100 ms? Are you have resistor 120 om in your CAN sender?


What you mean about 267 ?

ID267=OP_PENC_OPEL_FRONT (Bedienung Tastgeber Bedienelement Front), ZBE

267 - it is just buttons from i-drive controller

(10-12-2018, 10:38 AM)Coding34 Wrote:  For that i have made my own cables for the quadlock (including ETH_A with 1kOHM to 12v) ,
Haveto disconnect that fake

NBTEVO, ENAV2, MGU  - CP OFF, Navi , APPS , Carplay, AA
MGU ID-8-9-10 Cars - Full Region change

NCD Secure Coding 2.0




15-12-2018, 16:07 PM, (This post was last modified: 15-12-2018, 16:09 PM by billyballs.)
Post: #9
RE: NBT EVO HW4.1 on the bench
BugFix where do you get the info from the CAN bus ?

I mean this:

(14-12-2018, 21:04 PM)BugFix Wrote:  ID267=OP_PENC_OPEL_FRONT (Bedienung Tastgeber Bedienelement Front), ZBE

and this:

(13-12-2018, 22:31 PM)BugFix Wrote:  NM2_BODY_CAN
1379 (563h) - NBTevo_Rueko [21] {aktiv bei: KL_30B}

Zykluszeit: ttyp = 640.0 ms (tmin = 608.0 ms, tmax = 672.0 ms)
Aktivbedingung = KL_30
Startbedingung = KL_30_ON; Stopbedingung = KL_30_OFF
15-12-2018, 17:47 PM,
Post: #10
RE: NBT EVO HW4.1 on the bench
Google work fine for me

NBTEVO, ENAV2, MGU  - CP OFF, Navi , APPS , Carplay, AA
MGU ID-8-9-10 Cars - Full Region change

NCD Secure Coding 2.0






Possibly Related Threads…
Thread Author Replies Views Last Post
XZBMW Tool for bench read 8hp Garryq 9 1,558 26-03-2024, 09:32 AM
Last Post: skywoker
  Bosch MEVD172H bench backup mrproper 1 248 23-03-2024, 18:43 PM
Last Post: Ratnik1990
XZBMW ENAV2 bench activation Airbus 10 795 25-02-2024, 08:17 AM
Last Post: jb2005
  Motronic 3.3.1 bench jaramillo 3 172 13-02-2024, 05:12 AM
Last Post: 2013m5
  Dde Coding/flash with esys in bench? ruben_17non 0 183 08-02-2024, 21:28 PM
Last Post: ruben_17non
  Entrynav2 - Trying to Trigger Component Protection on Bench 2002JCW 5 464 30-01-2024, 16:44 PM
Last Post: DEJMIEN
XZBMW NBT display on bench without unit djordan 4 323 15-01-2024, 08:08 AM
Last Post: Powerlab
XZBMW cas / cluster bench setup Cniksor 103 23,806 09-01-2024, 09:43 AM
Last Post: MIKUr1
  Entrynav2 bench Jalami 1 295 06-01-2024, 15:28 PM
Last Post: Airbus
XZBMW ID8 bench CID can not light bbw 3 464 12-12-2023, 20:36 PM
Last Post: Airbus

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content