Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

F31 enet connection issue.
12-02-2022, 13:07 PM,
Post: #1
XZBMW  F31 enet connection issue.
Hello everyone, I just bought F31 from 2013 everything is right with car, but have problems with enet cable when tried to connect ista or esys. Ista show me vin and ip, but cant connect to the car like is not on ignition on. Esys say no zgw. Onnce I managed to connect to the car with the engine running, but reading speed was very low, took more than 5 minutes to read the vehicle info. I used the same cable and software configuration to many other f series cars without problem. Tried to connect ista via d can cable and connection was successful. I Used unicarscan adapter with bimmercode and bimmertool without any issues. Any suggestions what is could be wrong.  I'm sure cable and software is in working order.
Quote this message in a reply
12-02-2022, 13:40 PM, (This post was last modified: 12-02-2022, 13:45 PM by M-Simon.)
Post: #2
RE: F31 enet connection issue.
Try to Battery Reset the car. ->Remove negative terminal for 30 seconds. Then try again. Should work when your Equipment is okay
Reputation: +1 - morto [+1]
Quote this message in a reply
[+] 1 user says Thank You to M-Simon for this post
12-02-2022, 16:50 PM, (This post was last modified: 12-02-2022, 16:51 PM by larshutten.)
Post: #3
RE: F31 enet connection issue.
Or just let car go into sleep mode. After that connect enet cable. This usually happens when most adapters are connected before direct enet cable.

Sleep mode;
All illumination light of, start/stop button, hazard light button lights switch. If illumination light from those components is off you can assume car is in sleep.

Fastest way to achieve this is force sleep mode if possible with your tools. Or lock car and be patient can take up to 30min
Quote this message in a reply
12-02-2022, 20:57 PM,
Post: #4
RE: F31 enet connection issue.
(12-02-2022, 13:07 PM)morto Wrote:  Hello everyone, I just bought F31 from 2013 everything is right with car, but have problems with enet cable when tried to connect ista or esys. Ista show me vin and ip, but cant connect to the car like is not on ignition on. Esys say no zgw. Onnce I managed to connect to the car with the engine running, but reading speed was very low, took more than 5 minutes to read the vehicle info. I used the same cable and software configuration to many other f series cars without problem. Tried to connect ista via d can cable and connection was successful. I Used unicarscan adapter with bimmercode and bimmertool without any issues. Any suggestions what is could be wrong.  I'm sure cable and software is in working order.

is this continuous or sporadic?


Quote this message in a reply
12-02-2022, 21:42 PM, (This post was last modified: 12-02-2022, 21:45 PM by morto.)
Post: #5
RE: F31 enet connection issue.
Hi, yes continuous, from last 10 tries connection via enet cable with ista was successful only one time. And problem is only with this car. Today after an unsuccessful attempt to connect my car, I tried on my friend's f10, even without restarting ISTA and it connected without a problem in seconds.
p.s. I haven't tried to disconnect the battery yet.
Quote this message in a reply
12-02-2022, 21:58 PM,
Post: #6
RE: F31 enet connection issue.
(12-02-2022, 21:42 PM)morto Wrote:  Hi, yes continuous, from last 10 tries connection via enet cable with ista was successful only one time. And problem is only with this car. Today after an unsuccessful attempt to connect my car, I tried on my friend's f10, even without restarting ISTA and it connected without a problem in seconds.
p.s. I haven't tried to disconnect the battery yet.

10 times is considerable amount of tries to conclude that something is wrong with car. battery reset is usually a cure for enet when obd port is stuck from icom diagnosis.


Quote this message in a reply
[+] 1 user says Thank You to Sauron for this post
13-02-2022, 07:08 AM,
Post: #7
RE: F31 enet connection issue.
try that settings


Attached Files Thumbnail(s)
   
Quote this message in a reply
[+] 1 user says Thank You to rana for this post
13-02-2022, 09:59 AM,
Post: #8
RE: F31 enet connection issue.
What version Ista ?
Quote this message in a reply
13-02-2022, 12:02 PM,
Post: #9
RE: F31 enet connection issue.
(12-02-2022, 13:07 PM) morto Wrote:  Hello everyone, I just bought F31 from 2013 everything is right with car, but have problems with enet cable when tried to connect ista or esys. Ista show me vin and ip, but cant connect to the car like is not on ignition on. Esys say no zgw. Onnce I managed to connect to the car with the engine running, but reading speed was very low, took more than 5 minutes to read the vehicle info. I used the same cable and software configuration to many other f series cars without problem. Tried to connect ista via d can cable and connection was successful. I Used unicarscan adapter with bimmercode and bimmertool without any issues. Any suggestions what is could be wrong.  I'm sure cable and software is in working order.
I had exactly same issues where Enet would work with other cars but would do exactly same for some f3x and f2x series ended up trying another Enet cable which solved the issues


Quote this message in a reply
13-02-2022, 14:19 PM, (This post was last modified: 13-02-2022, 14:20 PM by Bimmer540.)
Post: #10
RE: F31 enet connection issue.
This is a very good adapter and read very fast.


Price: $29.00
[Image: ENET_1r.jpg]
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  The issue from the seventh circle of hell,,, 530d mj_mj_mj 18 1,010 Yesterday, 14:07 PM
Last Post: ____ANGEL___
  I020 esys connection issue mcrussell 6 229 25-03-2024, 23:35 PM
Last Post: vanos
  FEM Not working with ENET but works wtih DCAN armenh7 0 52 25-03-2024, 00:04 AM
Last Post: armenh7
XZBMW E-Sys and direct ecu connection PASS_THRU lacost 2 156 18-03-2024, 18:38 PM
Last Post: VroomVroom
XZBMW Harman Kardon Most issue F10 Satia 3 160 14-03-2024, 07:09 AM
Last Post: vikro2000
  6WB Retrofit Issue painsage 5 308 06-03-2024, 17:02 PM
Last Post: painsage
  Ista D issue with VCX SE stjansdal 6 240 05-03-2024, 16:51 PM
Last Post: Transauto
  BMW K50 TPMS issue after unloking SLZ jaramillo 3 139 23-02-2024, 14:24 PM
Last Post: BMWzone
XZBMW F80 LCI Retrofit adaptive led ICON issue vld 9 555 22-02-2024, 14:10 PM
Last Post: vld
  F15 6WB retrofit issue, Kombi from F02 pretrofit 13 1,874 21-02-2024, 14:15 PM
Last Post: evaldazj

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content