[PaulF2022]

Hi Folks,

Anyone tried Enet programming? Is there anything special need to be done?

I've tried it successfully, nothing special, if Enet diagnostics works for you, just make sure you have a high current charger connected while doing programming.

Thanks, yeah diag works just fine.
Did you use just a static 169.254.1.1 as PC ip? Also, did you change anything in a config to allow enet programming (it is mentioned in a first message here).

[bereic]

HI
My X3 has been produced in November 2021. But there is no SSP Wiring diagrams for fron or taillights.
Does someone know why?

Or is maybe someone able to check with his installation?

On the attached picture the "Beleuchtung" is missing.

[petraki]

Hi Folks,

Anyone tried Enet programming? Is there anything special need to be done?

I've tried it successfully, nothing special, if Enet diagnostics works for you, just make sure you have a high current charger connected while doing programming.

Thanks, yeah diag works just fine.
Did you use just a static 169.254.1.1 as PC ip? Also, did you change anything in a config to allow enet programming (it is mentioned in a first message here).

Hi!
Usually it's the Windows autoassigned ip address in the range 169.254.0.0/16, just leave the windows config to auto, but then -- this is also the same as the diag you did.
Alter ISTAGUI.exe.config file, which is in the same dir as the ISTA executable you use to run the app.

There're the following lines in that file (looking at the latest version 4.34.2x):

Code:

<!-- enable Programming via ENET, don't use it with ICOM Nano! -->
    <add key="BMW.Rheingold.ISTAGUI.enableENETprogramming" value="false" />

Set the value false to true, save and you're done.
The config line should look like:

Code:

    <add key="BMW.Rheingold.ISTAGUI.enableENETprogramming" value="true" />

[BMWzone]

In latest release at me not works Air Mass Test on R60 N47 EDC17_C50, reinstalling nothing changes, Service Function show error ABL_DIT_AT1361_BX7_LMS. Tried others ICOM without differences.
In other laptop with release 4.33.30 works good, same ICOM, same car.

Can anyone execute this test ?

[Bimmer540]

So there is something missing on other laptop...

[Spitfire555]

HI
My X3 has been produced in November 2021. But there is no SSP Wiring diagrams for fron or taillights.
Does someone know why?

Or is maybe someone able to check with his installation?

On the attached picture the "Beleuchtung" is missing.

Search at the bottom for "Funktionsschaltpläne", maybe there are the data you search for.

[bereic]

Search at the bottom for "Funktionsschaltpläne", maybe there are the data you search for.

Hi
Thanks, but FUB is different from SSP. FUB doesn't show the wiring colors, size, Pin# nor any details. 

So not sure if this is only related to the ISTA Version or a problem of this release. 
My BMW Dealer has them on the newst version available, but he isn't able to check if these were available in previous versions. 

I hope maybe someone can check on newer version than 4.34.20.

[Spitfire555]

Thanks, but FUB is different from SSP. FUB doesn't show the wiring colors, size, Pin# nor any details. 

I doesn't mean FUB (= Funktionsbeschreibung).

With the "Funktionsschaltpläne" you can see which is connected to whom and mostly also the pinning. Only the wire colors cannot be found.

[bereic]

yeah wire colors an which PIN goes where... and that exactly what i am looking for.
Hopefully with a future release from @Sedoy this will be fixed.

[florinu]

Somebody have a download link for ISTA 4.33.x ?