Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

F & G series - Slow programming speed
04-07-2022, 08:44 AM,
Post: #11
RE: F & G series - Slow programming speed
Your problem is: Subnet mask does not match with subnet mask of master gateway. That is the reason it can't switch to http. You need to check the network settings in a gateway unit and compare to the ones in your computer.
Quote this message in a reply
[+] 1 user says Thank You to Node for this post
04-07-2022, 09:27 AM,
Post: #12
RE: F & G series - Slow programming speed
How can I check settings in gateway?

I tried now on Enet cable and it throws me this: 
Code:
<MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]>

<MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]>
<MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]>
<MCDDiagService<id=242900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_SDB - RoutineControl SetDefaultBus, description=error: timeout, link=HU_NBT2_63_ETHERNET_63> [DIAGSERVICE]>
<[] Activate programming mode was not successful for: ECUId:HU_NBT2_0x63 [WARN]>
<[] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [WARN]>
<[HU_NBT2 - 63] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [THROWABLE]>
<[] ECUId:HU_NBT2_0x63 not accessible cause could not be switched to parallel programming mode [WARN]>
 

Slightly different
Quote this message in a reply
04-07-2022, 09:35 AM,
Post: #13
RE: F & G series - Slow programming speed
You can't just switch from ICOM to ENET as ICOM has DHCP server and provides different address range to gateway. Of course you could have DHCP server on your ENET and it could work. Given you had the previous error with ICOM it is possible that someone did some changes to IP config of gateway before. I think best way for you is to disconnect the car battery for a minute so gateway resets it's IP configuration.
Quote this message in a reply
[+] 1 user says Thank You to Node for this post
04-07-2022, 16:22 PM,
Post: #14
RE: F & G series - Slow programming speed
Thanks!
I have discovered that someone have retrofitted NBT Evo in this G30 so thats probably why I cant flash it. What can cause it? As far I know BDC is the same for HU-B and HU-H so there shouldn't be gateway mismatch
Quote this message in a reply
[+] 1 user says Thank You to Krysiaman for this post
04-07-2022, 16:43 PM,
Post: #15
RE: F & G series - Slow programming speed
There are functions in tool32 for BDC to set IP address, mask, etc. I just don't remember what they are called. It could be someone changed default setting or something.
Quote this message in a reply
[+] 1 user says Thank You to Node for this post
04-07-2022, 19:45 PM,
Post: #16
RE: F & G series - Slow programming speed
(04-07-2022, 16:22 PM)Krysiaman Wrote:  Thanks!
I have discovered that someone have retrofitted NBT Evo in this G30 so thats probably why I cant flash it. What can cause it? As far I know BDC is the same for HU-B and HU-H so there shouldn't be gateway mismatch

can you ping 169.254.199.99 ?

Coding 2.0 File Service - Region Change/Typekey
BMW Full FSC Set + CarPlay - NBT EVO ID4/5/6/ENTRYNAV2 (CP REMOVE/PATCH)
MGU CARPLAY/ANDROID AUTO Activation / MGU PATCH/CP REMOVE (EU service)
ISN RESET Remote F/G series
BMW KAFAS 2/4 FSCs(7E/BE/BF - 11F/13E/13F)
BMW KAFAS4/MRR/RAM Virgin / VIN FSC Matching
Quote this message in a reply
05-07-2022, 07:22 AM,
Post: #17
RE: F & G series - Slow programming speed
(04-07-2022, 19:45 PM) dasi Wrote:  
(04-07-2022, 16:22 PM)Krysiaman Wrote:  Thanks!
I have discovered that someone have retrofitted NBT Evo in this G30 so thats probably why I cant flash it. What can cause it? As far I know BDC is the same for HU-B and HU-H so there shouldn't be gateway mismatch

can you ping 169.254.199.99 ?

nope

   
   

Checked OABR and it's connected. Pin 1 and 3 goes to BDC. There is also something more in EVO OABR but I assume it's ATM.

EDIT:
Just checked ipconfig using DEV_UDS:
Code:
  STAT_IPADDRESS                  = 169.254.199.99

  STAT_NETMASK                    = 255.255.0.0
  STAT_GATEWAY                    = 0.0.0.0
  JOB_STATUS                      = OKAY
Quote this message in a reply
07-07-2022, 19:07 PM,
Post: #18
RE: F & G series - Slow programming speed
Just thinking:
Could it be bad BDC? There was only one BDC hardware version for whole G30 range?
Quote this message in a reply
07-07-2022, 19:55 PM,
Post: #19
RE: F & G series - Slow programming speed
And what is the config of your computer???
Quote this message in a reply
15-09-2022, 19:02 PM,
Post: #20
RE: F & G series - Slow programming speed
Looks like my problem is somehow gone. When I use router (real, not software) and always disconnecting battery for a while before connecting icom and ista/esys I don't have any issues with Ethernet and programming goes fast. Tried today on F06 with EVO. When I started programming using build-in ICOMs DHCP server programming was very slow. I have aborted it and then connected via Router and also disconnected battery for a while and then it went in normal speed



And about that exact G30 which didn't want to ping IP: there actually was a problem with OABR. Fixed wirings and everything works fine
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Making F-series combox work in e-series Ryn079 1 164 11 hours ago
Last Post: Marx
  mileage g series virtual bosch id7 tigre 2 219 22-03-2024, 13:00 PM
Last Post: tigre
ZSkoda Solved ✔ ISTA Standalone WLAN programming botho 4 336 21-03-2024, 11:13 AM
Last Post: botho
XZBMW G Series KEY in F34 Rajco 5 362 20-03-2024, 18:56 PM
Last Post: Rajco
XZBMW F15 Programming Error mcrussell 7 389 20-03-2024, 05:38 AM
Last Post: SweetBMW
XZBMW BMW X6 E71 Programming Ryzen 5 196 16-03-2024, 12:42 PM
Last Post: Node
XZBMW G20 Speed Limiter? bmchicago 1 109 06-03-2024, 18:37 PM
Last Post: Node
XZBMW Solved ✔ Cic update on E series alsamaraee 16 791 28-02-2024, 11:38 AM
Last Post: alsamaraee
XZBMW ISTA/P is no longer supported for F, G & I series see_you_33 22 5,172 20-02-2024, 04:49 AM
Last Post: Alenorm
XZBMW problem with flashing CHAMP2 module (the programming dependencies are not correct) azwgh 17 667 11-02-2024, 19:39 PM
Last Post: azwgh

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content