Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Solved ✔ D-can not working after using Enet
30-09-2022, 11:23 AM,
Post: #11
|
|||
|
|||
RE: D-can not working after using Enet
Try reloading FTDI drivers
|
|||
30-09-2022, 11:28 AM,
Post: #12
|
|||
|
|||
RE: D-can not working after using Enet
i had a similar problem, i just reinsalled ista again without uninstalling anything, just run install again, it goes through the procedure from the start again where you can choose dkan cable again, it worked for me, goodluck
|
|||
30-09-2022, 12:02 PM,
Post: #13
|
|||
|
|||
RE: D-can not working after using Enet
Thaks
Will do re-instal ista and try it again. Will inform you later or tomorrow. Thanks Again |
|||
Reputation: +1 - al70 [+1] | |||
30-09-2022, 12:24 PM,
Post: #14
|
|||
|
|||
RE: D-can not working after using Enet
i can check for u
text me whatsapp 00218927192507 |
|||
30-09-2022, 20:02 PM,
Post: #15
|
|||
|
|||
RE: D-can not working after using Enet
Why don’t you down load the Konfigulator for INPA? I hope still posted, I used it and never problem. My cable is Omitec “bought from eBay few years ago” for e86 and ENET for F32.
|
|||
30-09-2022, 22:13 PM,
(This post was last modified: 30-09-2022, 22:27 PM by BMWAPC.)
Post: #16
|
|||
|
|||
RE: D-can not working after using Enet
Before unistall it have you changed the settings in ISTA back to Ediabas?
|
|||
Reputation: +1 - al70 [+1] | |||
01-10-2022, 08:20 AM,
Post: #17
|
|||
|
|||
RE: D-can not working after using Enet
|
|||
01-10-2022, 08:37 AM,
Post: #18
|
|||
|
|||
RE: D-can not working after using Enet
|
|||
Reputation: +1 - al70 [+1] | |||
01-10-2022, 10:15 AM,
Post: #19
|
|||
|
|||
RE: D-can not working after using Enet
(01-10-2022, 08:37 AM)noobontour Wrote:(30-09-2022, 22:13 PM)BMWAPC Wrote: Before unistall it have you changed the settings in ISTA back to Ediabas? Ok I have only just seen the OP image of his ISTA Settings. It strange why it won't connect if everything is correct. |
|||
01-10-2022, 10:41 AM,
Post: #20
|
|||
|
|||
RE: D-can not working after using Enet
(01-10-2022, 10:15 AM)BMWAPC Wrote:(01-10-2022, 08:37 AM)noobontour Wrote:(30-09-2022, 22:13 PM)BMWAPC Wrote: Before unistall it have you changed the settings in ISTA back to Ediabas? Yes its really strange. Maybe a uninstall/reinstall of the cable ftdi drivers could help. |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content