[Siki78]

The vin which is used for rtti must it be the same as the head unit?
Cause atm and hu won''t talk to each other if there is a vin mismatch.

Save your original vin(in HEX) and fdl code it after you see that rtti and weather is working just don`t update services over HU.

---

Dpas index did you checked?
Try to run tool32 like admin and disable antivirus

yes, DPAS_INDEX -> dpas_2

tool32 setting always to admistrator

i will check also swich off antuwirus, but tools32 work many months on my laptop, all ok, just this method don't work

I tried by enet and also by icom

If you want I can try remotley over teamviewer

hi 
see here, tried many times yesturday, always was error. 
Today moring I saw active RTTI:



Wheather still not active

Don`t know what is happend but we can stil try over remote to see what is blocking your xml.

[Wojti77]

Just use this
3;c:\file.xml;2
Without ""
Did you put file.xml in C:\
If you need any help let me know I am at home

yes file on C:


 Post: #70 
also I had error

wow, finally activated RTTI and whaether
cleaned status and some minutes ago tried again. 2 min later all activated
used Icom for activation

thanks @Siki78 for support

   

[Fx82]

I activated rtti + weather on the bench for evo id6 + atm and it works.
Big shout out to Siki78

Another question is there also a solution for E series cic + combox and F series?

[laso]

I activated rtti + weather on the bench for evo id6 + atm and it works.
Big shout out to Siki78

Another question is there also a solution for E series cic + combox and F series?

Can you tell how? Do you use HU Engiennering for this

[Siki78]

I activated rtti + weather on the bench for evo id6 + atm and it works.
Big shout out to Siki78

Another question is there also a solution for E series cic + combox and F series?

Can you tell how?  Do you use HU Engiennering for this

@laso
Read post #18 if you need some help write me pm

[r2p]

1. Read ECU using E-Sys (launcher, esysx, esysplus)
2. Read Coding Data from HU
3. Search for „LONGVIN”
4. Change werte to the VIN with active services - examples on PM after thx/rep.
5. Save CAFD
6. Code FDL
7. Close E-Sys. Won’t be needed anymore.
8. Go to TOOL32
9. Load enavevo.prg(nbtevo.prg)
10. Click steuern_routine and choose provisioning in argument field, run job (F5).
11. Wait 1 minute
12. Click steuergerate_reset

Hi, thank you very much for your instructions. I'm just about to test it, but unfortunately after the fdl coding with a other VIN, the menu items under connected drive disappear and no more services are loaded. It can be due to the ilevel 11/22. I followed the instructions exactly and took a VIN that is not yet 3 years old so that I am sure that the services are available.

Which ilevel are you using?

Thx in advance

[Siki78]

Write me pm I can try over teamviewer. And please if you doing on bench be sure you have good signal strenght

[r2p]

Write me pm I can try over teamviewer. And please if you doing on bench be sure you have good signal strenght

Hi Siki78,
I've tried it a few more times and flashed everything back to the original vin, and performed an atm provisioning reset and start a provisioning with origin VIN after that i followed your instructions and now it's working, thank you very much for your help 

[pyzdraaaa]

Just use this
3;c:\file.xml;2
Without ""
Did you put file.xml in C:\
If you need any help let me know I am at home

yes file on C:


 Post: #70 
also I had error

i have the same problem as you. how did you solve your problem?

[pyzdraaaa]

Just use this
3;c:\file.xml;2
Without ""
Did you put file.xml in C:\
If you need any help let me know I am at home

yes file on C:


 Post: #70 
also I had error

wow, finally activated RTTI and whaether
cleaned status and some minutes ago tried again. 2 min later all activated
used Icom for activation

thanks @Siki78 for support

i have the same problem as you. how did you solve your problem?