Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
Ultimate Ediabas/ISTA+ voltage control V3
09-07-2023, 07:44 AM,
Post: #311
|
|||
|
|||
RE: Ultimate Ediabas/ISTA+ voltage control V3
(08-07-2023, 16:50 PM)b3dn Wrote: With D-Cable it runs fine. I was able to delete adaptions finally Great Work. You get C:\ediabas when you install standard tools. Uninstall them and it will be removed (at least most of it , but you can delete it afterwards. I am not familiar with openport. HOW do you use it in ediabas??? |
|||
09-07-2023, 07:57 AM,
Post: #312
|
|||
|
|||
RE: Ultimate Ediabas/ISTA+ voltage control V3
(09-07-2023, 07:44 AM)Node Wrote: You get C:\ediabas when you install standard tools. Uninstall them and it will be removed (at least most of it , but you can delete it afterwards. Thx for the Info. First i´ve set up an ordinary Dcan Cable in ediabas with your voltage control. Everything is fine. Now, i´ve set up openport as passthru in ISTA+ settings. It reads voltage but no ignition. Setting up that device in ediabas as interface=passthrud but i´ve no luck. Will investigate it, maybe wrong settings.... If i got it running via ediabas is it possible to set up the voltage control on passthru devices (passthrud.dll renamed to passthrud.ebas.dll)? |
|||
09-07-2023, 08:22 AM,
Post: #313
|
|||
|
|||
RE: Ultimate Ediabas/ISTA+ voltage control V3
(09-07-2023, 07:57 AM)b3dn Wrote:(09-07-2023, 07:44 AM)Node Wrote: You get C:\ediabas when you install standard tools. Uninstall them and it will be removed (at least most of it , but you can delete it afterwards. It could be. |
|||
25-01-2024, 15:47 PM,
Post: #314
|
|||
|
|||
RE: Ultimate Ediabas/ISTA+ voltage control V3
Any chance off support 4.41.41 ? Thanks
|
|||
25-01-2024, 16:30 PM,
Post: #315
|
|||
|
|||
RE: Ultimate Ediabas/ISTA+ voltage control V3
(25-01-2024, 15:47 PM)7eventy7even Wrote: Any chance off support 4.41.41 ? Thanks For what you need it? I succesfully tested newest ISTA with D-Can without VoltageControl. Maybe is depend on D-Can Adapter, i don't know. Only for optical display fake Voltage? |
|||
25-01-2024, 17:43 PM,
Post: #316
|
|||
|
|||
RE: Ultimate Ediabas/ISTA+ voltage control V3
(25-01-2024, 16:30 PM)Sedoy Wrote:(25-01-2024, 15:47 PM)7eventy7even Wrote: Any chance off support 4.41.41 ? Thanks I have problem with ignition,dont need optical display, its not working with my cable... maybe old one... and need new one ?! |
|||
25-01-2024, 18:21 PM,
(This post was last modified: 25-01-2024, 18:32 PM by Sedoy.)
Post: #317
|
|||
|
|||
RE: Ultimate Ediabas/ISTA+ voltage control V3
Ok, if not working with your cable then need VoltageContol.
Here only IstaOperation.exe v4.41.41.25274, all other files use from old archive. |