Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]

Problem with honda accord 2009 needle
05-12-2015, 13:15 PM,
Post: #1
RHonda  Problem with honda accord 2009 needle
Car honda accord 2009
problem with needle

i have disassemble the dash to correct the mileage
I have push up the needle to remove them
i have connect st01 cable to 93c86 eeprom ( i have not desolder it ) i have enter eeprom on digiprog to read it to make a back up .. when i pressed read it i hear all motor stepper moving
and same thing happen when i have write the eeprom i heard all motor stepper moving.
i have recalibrate the needle.
but now i have problem with fuel needle...
i have mark the starting position ... when customer drive car after 2-3 day the fuel needle will jump over, it doesn’t come to start position .i have remove the needle and re-calibrate it more then 5 time.
i test it in turning ignition to on and off more then 30 times repetitively .. its work fine when I turn ignition to on the needle move up and when I turn off the needle move down to star position.. but when customer take the car after 2 day its jump over...
i think that the needle don't fell down to start position sometime after turning the car off .. that's why it over jump when turning ignition again to on
any idea on how to fix it?
I have post the needle model


Attached Files Thumbnail(s)
       
Quote this message in a reply
07-12-2015, 13:37 PM,
Post: #2
RE: Problem with honda accord 2009 needle
Hi..try to lift neadle for 1mm..sometimes problem is the nedle became to short to fit back..


Attached Files Thumbnail(s)
   
Quote this message in a reply
07-12-2015, 15:38 PM,
Post: #3
RE: Problem with honda accord 2009 needle
Just grab a new dash and do from rear solder points , that dash is cheap, keep your customers happy ,

If my post was helpful, please take the time to click +Thanks and +Reputation.
under under
East Coast Smelecom Authorized Factory Dealer
Sales ,Tech support .
Only deal with Authorized Dealers ,East Coast(Smelecom)Distribution
Smelecom Authorized Dealer
Sales,Tech support.
Authorized Dealer For:
USA ELPROSYS DP4 DEALER https://diagprog4.com/
USA JDiag Dealer http://www.jdiag.com/
USA Repsoft DIGIPROG4 REPSOFT ERASER CAS4 PROGRAMMER Dealer/Sales
More brands coming Soon


cheers cheers
Quote this message in a reply
07-12-2015, 19:42 PM,
Post: #4
RE: Problem with honda accord 2009 needle
(07-12-2015, 13:37 PM)alex.eobd2 Wrote:  Hi..try to lift neadle for 1mm..sometimes problem is the nedle became to short to fit back..

hello the needle is lifted ok do you think there another solution ?
Quote this message in a reply
07-12-2015, 19:55 PM,
Post: #5
RE: Problem with honda accord 2009 needle
Probably dead motor..if nedle is feted as shuld and wont work you need to change motor or like XmoDDeR sayed.. good luck
Quote this message in a reply
07-12-2015, 20:09 PM,
Post: #6
RE: Problem with honda accord 2009 needle
(07-12-2015, 19:55 PM)alex.eobd2 Wrote:  Probably dead motor..if nedle is feted as shuld and wont work you need to change motor or like XmoDDeR sayed.. good luck

the needle work for 2-3 day correctly but after it don't get back to original position ...so i -recalibrate it and same problem come back again
Quote this message in a reply
07-12-2015, 20:16 PM,
Post: #7
RE: Problem with honda accord 2009 needle
Change the stepper motor from dash
and next time dont be lazy and remove the eeprom
Quote this message in a reply
07-12-2015, 21:35 PM,
Post: #8
RE: Problem with honda accord 2009 needle
He wasnt lazy he pulled the needles , all in vain as you can do this vehicle with all tools that support eprom programming from the back solder points without damage.

If my post was helpful, please take the time to click +Thanks and +Reputation.
under under
East Coast Smelecom Authorized Factory Dealer
Sales ,Tech support .
Only deal with Authorized Dealers ,East Coast(Smelecom)Distribution
Smelecom Authorized Dealer
Sales,Tech support.
Authorized Dealer For:
USA ELPROSYS DP4 DEALER https://diagprog4.com/
USA JDiag Dealer http://www.jdiag.com/
USA Repsoft DIGIPROG4 REPSOFT ERASER CAS4 PROGRAMMER Dealer/Sales
More brands coming Soon


cheers cheers
Quote this message in a reply
07-12-2015, 21:46 PM,
Post: #9
RE: Problem with honda accord 2009 needle
See if the stop needle is broken.
Ever happened to me something similar in another cluster (Peugeot 206). I had to put a stop to the needle and works well.


Attached Files Thumbnail(s)
   
Quote this message in a reply
07-12-2015, 21:49 PM,
Post: #10
RE: Problem with honda accord 2009 needle
Xmodder, I always remove the needles (where is possible) and always I remove the eep too, solder to r/w (not using clips) ( from 1998) and never had problems like this
Quote this message in a reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Mileage correction on Hilux 2009 MARTINS AUTOMECH 1 20 4 hours ago
Last Post: danocar
  Honda shadow 750 odometer file gozor 2 62 07-03-2024, 05:43 AM
Last Post: gozor
  Solved ✔ HONDA FREED HYBRID CHANGE OF KM Black Alien 2 89 05-03-2024, 11:03 AM
Last Post: Black Alien
  2009 toyota prado dash power up Black Alien 0 66 21-02-2024, 10:05 AM
Last Post: Black Alien
XZBMW Bmw cluster coding problem hukolo 2 130 20-02-2024, 23:53 PM
Last Post: jaramillo
RHonda Honda Varadero XL1000V 2007 L56R 93C56 Mileage correction foxik33 5 189 18-02-2024, 16:45 PM
Last Post: nikolanik
  honda nc 750 mileage corection krzysztof2908 3 138 10-02-2024, 10:17 AM
Last Post: Clusters
  Solved ✔ Honda CRB125 pyvotel 3 125 01-02-2024, 05:47 AM
Last Post: pyvotel
  Vw Polo 6r dash km change problem 2009mohrice 10 315 07-01-2024, 17:10 PM
Last Post: 2009mohrice
XZBMW EWS4.4 2L86D X3 eep problem Vampire123 3 640 28-12-2023, 09:04 AM
Last Post: foxportal

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content