[jojo1212]

This is full BDM read,
help plz

thank you

[ROD-BENDERS]

This is full BDM read,
help plz

thank you

Jojo I ran this file through my dpf delete software and it switched off 15 dpf maps. I then ran it through my egr delete soft and it removed the egr.

try this file and see if your dtc's are gone.

[jojo1212]

Car drives fine no problems.
only fault p2002 comes on every day
i will try your file. hope this solves it
thank you

[som3astar]

Hello
I have these two codes in tucson
P2002+p1405
When the code p2002 shows up
The car won't rev over 3000 rpm !?
When erase the code it revs fine
Does deleting the codes will make the car revs fine ? -dtc off- or need to do dpf off +egr off ? To make the car drives fine and revs fine ?
Thanks

[ROD-BENDERS]

Hello
I have these two codes in tucson
P2002+p1405
When the code p2002 shows up
The car won't rev over 3000 rpm !?
When erase the code it revs fine
Does deleting the codes will make the car revs fine ? -dtc off- or need to do dpf off +egr off ? To make the car drives fine and revs fine ?
Thanks

Hi you have dpf problem my friend

[som3astar]

Hello
I have these two codes in tucson
P2002+p1405
When the code p2002 shows up
The car won't rev over 3000 rpm !?
When erase the code it revs fine
Does deleting the codes will make the car revs fine ? -dtc off- or need to do dpf off +egr off ? To make the car drives fine and revs fine ?
Thanks

Hi you have dpf problem my friend

Hey friend .yes i do have a problem with dpf
Righ now i changed the D/pressure sensor and have a ride to test it

Have any suggestions friend?

[ROD-BENDERS]

Hello
I have these two codes in tucson
P2002+p1405
When the code p2002 shows up
The car won't rev over 3000 rpm !?
When erase the code it revs fine
Does deleting the codes will make the car revs fine ? -dtc off- or need to do dpf off +egr off ? To make the car drives fine and revs fine ?
Thanks

Hi you have dpf problem my friend

Hey friend .yes i do have a problem with dpf
Righ now i changed the D/pressure sensor and have a ride to test it

Have any suggestions friend?

P1405 Hyundai EGR Temperature Incorrect
Possible causes
Faulty Differential Pressure Feedback Electronic (DPFE) sensor (EGR pressure sensor)
Plugged or damaged EGR tube
Differential Pressure Feedback Electronic (DPFE) sensor harness is open or shorted
Differential Pressure Feedback Electronic (DPFE) sensor circuit poor electrical connection

have you checked these things too

[som3astar]

[/quote]

P1405 Hyundai EGR Temperature Incorrect
Possible causes
Faulty Differential Pressure Feedback Electronic (DPFE) sensor (EGR pressure sensor)
Plugged or damaged EGR tube
Differential Pressure Feedback Electronic (DPFE) sensor harness is open or shorted
Differential Pressure Feedback Electronic (DPFE) sensor circuit poor electrical connection

have you checked these things too
[/quote]

Now p1405 egr temp. Incorrect is gone
Dont shows up
I tested the car few minutes ago . Changed the d /pressure . Its worked better . But some times stalls on 3000 rpm .
Code shown is p2002
. While driving . I switch ignition off and on . And the car drives normal !
.
I cleand the dpf earlier . And tried to regenrate . It fails
Due to tempreture not reached the specific value
Replace it in programming and keeps throw p2002 like it clogged or something !!

[ROD-BENDERS]

P1405 Hyundai EGR Temperature Incorrect
Possible causes
Faulty Differential Pressure Feedback Electronic (DPFE) sensor (EGR pressure sensor)
Plugged or damaged EGR tube
Differential Pressure Feedback Electronic (DPFE) sensor harness is open or shorted
Differential Pressure Feedback Electronic (DPFE) sensor circuit poor electrical connection

have you checked these things too
[/quote]

Now p1405 egr temp. Incorrect is gone
Dont shows up
I tested the car few minutes ago . Changed the d /pressure . Its worked better . But some times stalls on 3000 rpm .
Code shown is p2002
. While driving . I switch ignition off and on . And the car drives normal !
.
I cleand the dpf earlier . And tried to regenrate . It fails
Due to tempreture not reached the specific value
Replace it in programming and keeps throw p2002 like it clogged or something !!
[/quote]

If there are two pressure sensors, one upstream and one downstream have you changed the other ?

If ecu type is EDC16C39 I can remove DTC's from flash.

Or It might be better to just remove the DPF in the ecu is the ecu listed in my soft ?

Post up your file if you want anything removed.

[som3astar]

I told the customer to come back next week so i would work on the car . I will change the pressure sensor that located after the dpf
Thank u

I sent u pm