Please make sure you read Rules! and DO NOT upload/post any illegal softwares or Pirated Material , Thank you for understanding :)
  1. AutoHex II

  2. FemtoEVO



Need help setting up j2534 with ista
13-05-2016, 01:15 AM,
Post: #1
Need help setting up j2534 with ista
Broke my icom and waiting for replacement and need help setting up my j2534 launch box to make it work for now. Can't figure it out, nothing works angry can someone help via TeamViewer, can pay paypal. Thx.

Sent from my HTC One_M8 using Tapatalk
Quote this message in a reply
13-05-2016, 01:40 AM,
Post: #2
RE: Need help setting up j2534 with ista
(13-05-2016, 01:15 AM)nymike Wrote:  Broke my icom and waiting for replacement and need help setting up my j2534 launch box to make it work for now. Can't figure it out, nothing works angry can someone help via TeamViewer, can pay paypal. Thx.

Sent from my HTC One_M8 using Tapatalk

This was from someone else (sweetsam I think). I don't remember who but it works.

in ediabas.ini interface must be changed to "pasthrud"

1- Rheingold system installed
2- BMW standerd tool 2.12
3- every passthru tool comes with its drivers cd
4- pttbmw v xxx im using v2.1
5- ediabas configuration tool


after complete step 1 start install bmw standerd tool 2.12 with check box ,inpa ediabas , ncexpert ,winkfp, choose std:obd for hardware for interface ,com 9 for com port ,
finish and restart pc ,now after restarting pc you have to install you tool drivers (passthur) ,
then install pttbmw vxxx (i prefer v2.1) open start>all program>bmw passthrud >passthrud configration and select your tool from the list check in k-line support for 115200bps
press launch confing tool complete by pressing ok , now open program file >bmw ag >passthrud > make copy for all files in this folder exept ediabas.bin file and
paste in c:\ediabas\bin\replace all files with the copy you made , use ediabas configration tool to chanege from std:obd to passthrud ,
start Rheingold and open setting select vci config select EDIABAS STANDARD SITTING and close setting , work done .

this system now ready to work with bmw cars with one tool using inpa,ncsexpert tool ,winkfp and bmw Rheingold (ISTA-D)
Quote this message in a reply
13-05-2016, 01:40 AM,
Post: #3
RE: Need help setting up j2534 with ista
I saw it, followed and not working.

Sent from my HTC One_M8 using Tapatalk
Quote this message in a reply
13-05-2016, 01:41 AM, (This post was last modified: 13-05-2016, 01:49 AM by eautocheck.)
Post: #4
RE: Need help setting up j2534 with ista
Edited since it did not help. Works for me but I do not know what steps you followed and I don't use teamviewer
Quote this message in a reply
13-05-2016, 02:22 AM,
Post: #5
Need help setting up j2534 with ista
Did as u posted but still no communication with the car. [Image: 9d740ffdaf049f1aaf9992d8159ad7d0.jpg]

Sent from my HTC One_M8 using Tapatalk
Quote this message in a reply
23-06-2019, 12:07 PM,
Post: #6
RE: Need help setting up j2534 with ista
K
(13-05-2016, 01:40 AM)eautocheck Wrote:  
(13-05-2016, 01:15 AM)nymike Wrote:  Broke my icom and waiting for replacement and need help setting up my j2534 launch box to make it work for now.  Can't figure it out,  nothing works angry  can someone help via TeamViewer,  can pay paypal.  Thx.

Sent from my HTC One_M8 using Tapatalk

This was from someone else (sweetsam I think). I don't remember who but it works.

in ediabas.ini interface must be changed to "pasthrud"

1- Rheingold  system installed
2- BMW standerd tool 2.12
3- every passthru tool comes with its drivers cd  
4- pttbmw v xxx  im using v2.1
5- ediabas configuration tool


after complete step 1 start install bmw standerd tool 2.12 with check box ,inpa ediabas , ncexpert ,winkfp, choose std:obd for hardware for interface ,com 9 for com port ,
finish and restart pc ,now after restarting pc you have to install you tool drivers (passthur) ,
then install pttbmw vxxx (i prefer v2.1) open start>all program>bmw passthrud >passthrud configration and select your tool from the list check in k-line support for 115200bps
press launch confing tool complete by pressing ok , now open program file >bmw ag >passthrud > make copy for all files in this folder exept ediabas.bin file and
paste in c:\ediabas\bin\replace all files with the copy you made ,  use ediabas configration tool to chanege from std:obd to passthrud ,
start Rheingold  and open setting select vci config select EDIABAS STANDARD SITTING and close setting ,  work done  .

this system now ready to work with bmw cars with one tool using inpa,ncsexpert tool ,winkfp and bmw Rheingold  (ISTA-D)

(13-05-2016, 02:22 AM)nymike Wrote:  Did as u posted but still no communication with the car. [Image: 9d740ffdaf049f1aaf9992d8159ad7d0.jpg]

Sent from my HTC One_M8 using Tapatalk

Pulling up this old trend. Did you get the J2534 passthrud working gents?

Can you give us all an update?
Quote this message in a reply


Possibly Related Threads...
Thread Author Replies Views Last Post
XZBMW ISTA-D 4.18.24 Standalone spider80 0 28 24 minutes ago
Last Post: spider80
XZBMW Ista 4.18.2 install files tonemoz 0 98 2 hours ago
Last Post: tonemoz
  BMW Release Notes ISTA/P 4.18.2x myfirst1er 2 310 11 hours ago
Last Post: sguzzel
  ISTA Launcher Console v1.2 Sedoy 11 808 Yesterday, 15:32 PM
Last Post: Sedoy
  ISTA Launcher Console v1.1 pshoey 70 24,419 16-07-2019, 17:58 PM
Last Post: Sedoy
  ISTA 4.18.14 license problem Fatalix 19 1,071 14-07-2019, 20:59 PM
Last Post: uragan1987
XZBMW ISTA Standalone / SQLiteDBs / BLP / PSdZData_Lite - latest [MEGA] Sedoy 273 38,427 13-07-2019, 22:36 PM
Last Post: Sedoy
  Release Notes ISTA V 4.18.1 Transauto 1 266 11-07-2019, 14:06 PM
Last Post: jogi8850
  Activation code file corrupt error in ista p keddy_ovi 1 131 11-07-2019, 11:18 AM
Last Post: jirkon
XZBMW Please help me understand: ISTA P, D, +.... icandolikeyoo 6 511 09-07-2019, 20:58 PM
Last Post: icandolikeyoo

Forum Jump:


Users browsing this thread:
1 Guest(s)

Return to TopReturn to Content