Unfortunately we do not accept new members for free, Now Registration cost 30€, if you are interesting Send Email to [email protected]
ICOM NEXT Firmware FW-3.14.10 released
25-08-2016, 17:09 PM,
Post: #11
|
|||
|
|||
RE: ICOM NEXT Firmware FW-3.14.10 released
Only with a valid license! Just to prevent against misunderstandings
|
|||
25-08-2016, 19:19 PM,
Post: #12
|
|||
|
|||
RE: ICOM NEXT Firmware FW-3.14.10 released
Hi to all i may ask stupid question but i don't know how to update next :/ is a same as A1 & A2 ? Can't figure out what to do with .msi file . Some people updating via Rheingold some via Ista p. Is any tutorial or video how to update. Thanks in advance.
|
|||
25-08-2016, 20:00 PM,
Post: #13
|
|||
|
|||
RE: ICOM NEXT Firmware FW-3.14.10 released
-Install it
-Start ISTA-D with Icom connected to your car -Go to connection manager and start the update. |
|||
25-08-2016, 21:17 PM,
Post: #14
|
|||
|
|||
RE: ICOM NEXT Firmware FW-3.14.10 released
|
|||
25-08-2016, 21:47 PM,
Post: #15
|
|||
|
|||
RE: ICOM NEXT Firmware FW-3.14.10 released
(25-08-2016, 21:17 PM)krug Wrote:(25-08-2016, 17:09 PM)Munich Simon Wrote: Only with a valid license! Just to prevent against misunderstandings Can also update like ICOM A1/2 via the browser interface using the tarballs I uploaded in post #2 ^^^. This is for people wary of .msi files. But its easier to just install the .msi and then upgrade via ISTA connection manager. If this post helped you in anyway please use the thanks and/or REP buttons down here. Thanks!
|
|||
25-08-2016, 22:46 PM,
Post: #16
|
|||
|
|||
RE: ICOM NEXT Firmware FW-3.14.10 released
|
|||
26-08-2016, 10:24 AM,
Post: #17
|
|||
|
|||
RE: ICOM NEXT Firmware FW-3.14.10 released
(25-08-2016, 22:46 PM)delete Wrote:(25-08-2016, 14:02 PM)Jynkky Wrote: Intresting. Have u configure your icom next to ispi next mode? by webserver of icom or ista d config same place as updating firmware If my post helped you hit the thanks and reputation button
|
|||
26-08-2016, 20:28 PM,
Post: #18
|
|||
|
|||
RE: ICOM NEXT Firmware FW-3.14.10 released
(26-08-2016, 10:24 AM)Jynkky Wrote:(25-08-2016, 22:46 PM)delete Wrote:(25-08-2016, 14:02 PM)Jynkky Wrote: Intresting. Have u configure your icom next to ispi next mode? Oh OK. Will check when I'll do the update... |
|||
27-08-2016, 11:39 AM,
Post: #19
|
|||
|
|||
RE: ICOM NEXT Firmware FW-3.14.10 released
(25-08-2016, 20:00 PM)snypertje Wrote: -Install it I tried that in home, only KL30 connected(13.8V), i supply voltage to OBD port only. Problem is, update wont see in ISTA-D. So shoul also KL15 need voltage, connect to car and then can, or what goes wrong? I have all ready installed that .msi to pc. Or how those extracted linux files should installing? Tried from web, but told " files are not for my ICOM...." (A2) Normally those files are . bin.... Was I helpful? Please support my time and Hit And -button's. NEW Trasdata 9 Master support Bosch SM(service mode) etc |
|||
27-08-2016, 14:06 PM,
Post: #20
|
|||
|
|||
RE: ICOM NEXT Firmware FW-3.14.10 released
Don't need KL15.
KL30 on pin 16 and ground on 4+5 is enough |
|||
« Next Oldest | Next Newest »
|
Users browsing this thread:
1 Guest(s)
1 Guest(s)
Return to TopReturn to Content